ASSEMBLY
The help of a second person is recommended. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Assembly requires only the
included hex key and wrench | . |
1.Identify the Right Upright (36); the Resistance Control/Cable (44) is routed through the Right Upright. Place the Base (14) near the Right Upright and the Frame (29). Have another person hold the Right Upright against the Base as shown.
Attach the Right Upright (36) to the Base (14) with two M8 x 63mm Bolts (38), two M8 Curved Washers (37), and two M8 Nylon Nuts (13) as shown. Make sure that the Curved Washers are turned so they conform to the curve of the Base. Do not tighten the Nylon Nuts yet.
Attach the Left Upright (35) to the Base (14) in the same way. Make sure that the Left Upright is oriented so the two indicated holes are on the side shown. Do not tight- en the Nylon Nuts yet.
2a.Raise the Left Upright (35) and the Right Upright (36) to
the position shown. Place the front of the Frame (29) between the Left Upright and the Right Upright. Connect the Reed Switch Wire (6) to the Short Reed Switch Wire
(A).
2b.Attach the Hood (28) to the front of the Frame (29) with two M5 x 10mm Bolts (10).
3.See drawing 3a. Locate the small incline knob on each side of the Frame. Slide the knobs into one of the three sets of slots in the brackets on the Uprights. Make sure that the knobs are fully inserted at the same height.
Look under the Frame (29) near the Left Upright (35). See drawing 3b. Locate the Clip (11) attached to the underside of the Frame. Insert the Reed Switch (6) into the Clip as shown. Next, locate the Magnet (12) on the left Flywheel (9). Turn the Flywheel until the Magnet is aligned with the Reed Switch. Move the Reed Switch so that there is a 3 mm (1/8 in.) gap between the Reed Switch and the Magnet. Then, tighten the M4 x 12mm Screw (3) in the Clip.
1 |
| 44 |
|
| |
| 36 |
|
|
|
|
13 | Bracket |
|
|
|
|
|
|
|
|
| |
37 | 14 |
|
| Holes | |
|
|
|
| ||
|
| 37 | 35 |
|
|
|
| 13 |
|
| |
37 |
|
|
|
|
|
38 | 13 |
|
|
|
|
|
|
|
|
| |
| 38 | 37 |
|
|
|
|
|
|
|
| |
2a |
| 29 | 36 |
|
|
|
|
|
| ||
| 6 |
|
|
|
|
35 |
|
|
|
|
|
| A |
|
|
|
|
2b | 10 |
|
|
|
|
|
| 28 |
|
|
|
|
|
|
| 29 |
|
|
|
|
|
| 10 |
3a | 35 | 3b | View from | ||
|
| beneath | |||
| Knob |
| |||
|
|
| 9 |
| |
Bracket |
|
|
|
| |
29 |
|
|
|
|
|
|
| 12 | 6 | 3 | 11 |
|
|
|
|
| |
|
| 3 mm | 29 |
| |
4