Weslo WCTL31304.0 user manual Troubleshooting, Problem The power turns off during use, Top, View

Page 15

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call the toll-free telephone number on the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 10. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill near the power cord. If the switch protrudes

 

 

 

as shown, the circuit breaker has tripped. To reset

Tripped

Reset

the circuit breaker, wait for five minutes and then

 

 

press the switch back in.

 

 

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker located on the treadmill frame near the power cord (see c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key into the console.

d. If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The speed display on the console does not function properly

SOLUTION: a. Remove the key and UNPLUG THE POWER CORD.

 

 

Remove the hood from the treadmill. Locate the Reed

3 mm

 

Switch (21) and the Magnet (43) on the left side of the

42

Pulley (42). Turn the Pulley until the Magnet is aligned

62

with the Reed Switch. Make sure that the gap be-

21

43

tween the Magnet and the Reed Switch is about

 

 

3 mm (1/8 in.). If necessary, loosen the Screw (62),

Top

 

move the Reed Switch slightly, and then retighten the

 

Screw. Reattach the hood, and run the treadmill for a

View

 

few minutes to check for a correct speed reading.

 

 

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model No. WCTL31304.0 Serial No QUESTIONS?Table of Contents Important Precautions Page Before YOU Begin Right SideBack Treadmill until it is completely assembled AssemblyMake sure that the power cord is not plugged Your own Phillips screwdriver Needlenose pliersPage Top View Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram STEP-BY-STEP Console OperationInsert the key into the console Follow your progress with the four displays When you are finished exercising, removeChange the incline of the treadmill as desired Measure your heart rate if desiredHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE View TroubleshootingProblem The power turns off during use TopProblem The walking belt slows when walked on Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Limited Warranty HOW to Order Replacement PartsKey Qty Description R0705AExploded Drawing Exploded Drawing B-Model No. WCTL31304.0 R0705A Exploded Drawing C-Model No. WCTL31304.0 R0705A
Top Page Image Contents