PART | R0905A |
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key No. | Qty. | Description | Key No. | Qty. | Description |
1 | 2 | Foot Rail | 52 | 2 | Rear Wheel |
2 | 1 | Left Front Endcap | 53 | 4 | Rear Wheel Cover |
3 | 23 | 3/4” Screw | 54 | 4 | Wheel Bolt |
4 | 2 | Frame Pivot Bolt | 55 | 6 | 1” Bolt |
5 | 2 | Rear Roller Washer | 56 | 1 | Left Wheel Bracket |
6 | 1 | Motor Belt | 57 | 1 | Right Rear Endcap |
7 | 1 | Front Roller/Pulley | 58 | 1 | Rear Roller |
8 | 1 | Magnet | 59 | 1 | Right Wheel Bracket |
9 | 2 | Frame Pivot Nut | 60 | 4 | 3/4” Bolt |
10 | 2 | Frame Spacer | 61 | 1 | Left Outer Cover |
11 | 2 | Idler Arm Washer | 62 | 1 | Latch Assembly |
12 | 2 | Frame Pivot Washer | 63 | 1 | Static Warning Decal |
13 | 9 | Nut | 64 | 1 | Pulse Assembly |
14 | 1 | Idler Arm Pulley | 65 | 1 | Right Inner Cover |
15 | 1 | Idler Pulley Bolt | 66 | 2 | Resistor Star Washer |
16 | 1 | Idler Arm Bolt | 67 | 2 | Lower Handrail |
17 | 1 | Idler Arm Bushing | 68 | 1 | Upper Handrail |
18 | 1 | Idler Arm | 69 | 1 | Console |
19 | 1 | Idler Arm Spring | 70 | 6 | Belly Pan Screw |
20 | 1 | Reed Switch | 71 | 22 | Screw |
21 | 5 | Small Screw | 72 | 1 | Access Door Screw |
22 | 1 | Sensor Clip | 73 | 2 | Upper Body Handle |
23 | 1 | Lift Frame | 74 | 2 | Rope Guide Bracket |
24 | 1 | Drive Motor | 75 | 1 | Top Housing |
25 | 2 | Motor Bolt | 76 | 1 | Walking Platform |
26 | 2 | Lift Frame Pivot Bolt | 77 | 1 | Controller Wire |
27 | 2 | Lift Frame Pivot Washer | 78 | 6 | Pulley |
28 | 1 | Controller | 79 | 4 | Pulley Nut |
29 | 2 | Controller Screw | 80 | 2 | Pulley Bolt |
30 | 2 | Warning Decal | 81 | 6 | Inside Cover Bolt |
31 | 1 | Ferrite Clamp | 82 | 2 | Fan |
32 | 14 | 1/2” Screw | 83 | 4 | Fan Screw |
33 | 1 | Power Board | 84 | 1 | Key Clip |
34 | 4 | Plastic | 85 | 1 | Power Cord Assembly |
35 | 1 | Electronics Bracket | 86 | 1 | Resistor |
36 | 1 | Hood Cover | 87 | 2 | Upright Pivot Bushing |
37 | 1 | Hood | 88 | 1 | Right Outer Cover |
38 | 1 | Belly Pan | 89 | 1 | Upright Pivot Shaft |
39 | 2 | Belt Guide | 90 | 2 | Upright Pivot Bolt |
40 | 1 | Right Front Endcap | 91 | 1 | Controller Plate |
41 | 2 | Front Walking Platform Screw | 92 | 1 | Tension Motor Wire |
42 | 4 | Walking Platform Screw | 93 | 6 | Base Pad |
43 | 1 | Frame | 94 | 10 | 3/4” Tek Screw |
44 | 4 | Belt Guide Screw | 95 | 1 | Upright Base Belly Pan |
45 | 4 | Isolator | 96 | 1 | Upright Base |
46 | 4 | Isolator Bolt | 97 | 2 | Washer |
47 | 1 | Latch Catch | 98 | 2 | 3” Bolt |
48 | 18 | Misc. Screw | 99 | 2 | Front Wheel |
49 | 2 | Endcap Plate | 100 | 2 | Incline Motor Bolt, Top |
50 | 1 | Left Rear Endcap | 101 | 1 | Incline Motor |
51 | 2 | Rear Roller Adj. Bolt | 102 | 1 | Incline Wire Harness |
34