Weslo 30863 user manual Troubleshooting, Problem The power does not turn on, Top View

Page 18

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and

follow the steps listed. If further assistance is needed, please see the front cover of this manual.

PROBLEM: The power does not turn on

 

 

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 11. Important: The treadmill is not com-

patible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has

 

 

tripped. To reset the circuit breaker, wait for five

Tripped

Reset

minutes, and then press the switch back in.

PROBLEM: The power turns off during use

 

 

 

 

 

SOLUTION: a. Check the reset/off circuit breaker located on the treadmill near the power cord (see c. above). If

the circuit breaker has tripped, wait for five minutes and then press the switch back in.

 

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for

five minutes, and then plug it back in.

 

 

 

 

 

c. Remove the key from the console. Reinsert the key into the console.

 

 

 

d. If the treadmill still will not run, see the front cover of this manual.

 

 

 

 

PROBLEM: The displays of the console do not function properly

 

 

 

 

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

 

65

20

 

POWER CORD. Remove the five indicated M4.2 x

25

 

10mm Screws (20) and the two M5.5 x 25mm Screws

20

 

 

20

(25). Then, carefully remove the Hood (65).

 

25

 

 

 

 

 

 

Locate the Reed Switch (97) and the Magnet (99) on

 

 

 

 

 

the left side of the Pulley (95). Turn the Pulley until

 

1/8 in.

 

 

 

the Magnet is aligned with the Reed Switch. Make

 

 

 

95

sure that the gap between the Magnet and the

 

97

 

 

Reed Switch is about 1/8 in. (3 mm). If necessary,

 

21

 

99

 

loosen the M4.2 x 13mm Screw (21), move the Reed

 

 

 

Switch slightly, and then retighten the Screw.

 

 

 

 

 

Reattach the Hood (not shown), and run the treadmill

Top View

 

 

 

for a few minutes to check for a correct speed read-

 

 

 

ing.

 

 

 

 

 

18

Image 18
Contents QUESTIONS? Model No Serial NoTable of Contents Important Precautions Never leave the treadmill unattended while itIs running. Always remove the key, unplug Page Before YOU Begin Assembly Page Not to scratch the face of the Console Assembly Repeat this step on the left side of the treadmillTies Plastic Make sure that the Latch Assembly is oriented As shown Four BoltsOperation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power Start the walking beltFollow your progress with the displays. The track-The track See HOW to Turn on the Power on See on HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The power does not turn on Top ViewProblem Solution Walking belt slows when walked onWalking belt. If the walking belt has shifted to Exercise Intensity HOW to Measure Your Heart Rate To measure your heartExercise Guidelines Workout GuidelinesSuggested Stretches Part LIST-Model No Key No. Qty. DescriptionKey No. Qty Description R0908A Exploded Drawing B-Model No Exploded Drawing C-Model No Exploded Drawing D-Model No Ordering Replacement Parts Limited Warranty