Sears 831.24733.0 user manual Problem Solution

Page 20

Locate the Reed Switch (89) and the Magnet (62) on the left side of the Pulley (71). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the M4.2 x t3mm Tek Screw (3), move the Reed Switch slightly, and then retighten the Screw.

Reattach the Hood (not shown), and run the treadmill for a few minutes to check for a correct speed reading.

PROBLEM: The walking belt slows when walked on

1/8

Top View

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.

b.If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few min-

utes. Repeat until the walking belt is properly tight- ened.

Rear Roller

Bolts

PROBLEM:

SOLUTION:

c.If the walking belt still slows when walked on, please see the back cover of this manual.

The walking belt is off-center or slips when walked on

a.If the walking belt has shifted to the left, first re- move the key and UNPLUG THE POWER CORD. Using the hex key, turn the left rear roller bolt clock- wise 1/2 of a turn. Be careful not to overtighten the walking belt. If the walking belt has shifted to the right, turn the left rear roller bolt counterclockwise 1/2 of a turn. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.

b.If the walking belt slips when walked on, first re- move the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts clock- wise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking plat- form. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and care- fully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

2O

Image 20
Contents Assembly Operation Maintenance Part List and Drawing Contents IMPORTANT Precautions Page Before YOU Begin Rubber malet AssemblyIncluded Page Page Console Wire Tie Page Top View HOW to Plug in the Power Cord PRE-LUBRICATED Walking BeltFeatures of the Console ConsolePlays HOW to Turn on the PowerHOW to USE the Manual Mode LgSB HOW to USE a Speed Workout Measure your heart rate if desiredHOW to USE the Stereo Sound System INFORMATiON ModeHOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE NOW to Fold the Treadmill for StorageTroubleshooting Problem SolutionProblem Solution Exercise GUiDELiNES Exercise FrequencyR12OZA QtyDescription Exploded Drawing A--IVlodeiNo .24733.0 R1207A Exploded Drawing B--IVlodei No .24733.0 m2ozA Exploded Drawing C--lVlodei No .24733.0 m2ozA Exploded Drawing D--IVlodei No .24733.0 m2ozA DAY Full Warranty Your Home