Sears 21-7119, 374.288450 Reset Switch 33 Replacement, Remove Console attaching Screws

Page 15

PARTS REPLACEMENT

Reset Switch (33) Replacement

Step 1. Remove MOTOR COVER (43).

Step 2. Remove wires from RESET SWITCH (33), one at a time to ensure proper attachment and install on new

RESET SWITCH. Refer to SPEED CONTROL SYSTEM WIRING DIAGRAM on page 12 if necessary.

Step 3. Remove RESET SWITCH (33) from POWER CORD BRACKET (31).

Step 4. Reinsert RESET SWITCH (33) into POWER CORD BRACKET (31) and attach MOTOR COVER (43).

Console (46), Fitness Computer (46a), And/Or Power Switch Replacement

Step 1. Remove CONSOLE attaching SCREWS (63).

Step 2. Slip CONSOLE (46) out of CONSOLE TUBE (40).

Step 3. Remove four SCREWS(46o) and one SCREW (46m) attaching FITNESS COMPUTER (46a) to CONSOLE

BOTTOM (46b).

Step 4. To replace FITNESS COMPUTER (46a), unplug FITNESS COMPUTER (46a) from WIRING HARNESS

(46g) and plug in new FITNESS COMPUTER. NOTE: Rep/ace any monitor casing needed.

Step 5. To replace POWER SWITCH (46k), remove wires from POWER SWITCH and attaching SCREW (461), snap POWER SWITCH out of the CONSOLE BOI-rOM (46b) and replace with new POWER SWITCH.

Step 6. Reassembly in reverse order - see SPEED CONTROL SYSTEM WIRING DIAGRAM if necessary.

Wiring Harness (46g) Replacement

Step 1. Remove MOTOR COVER (43).

Step 2. Remove CONSOLE (46) - see CONSOLEAND/OR POWER SWITCH REPLACEMENT. NOTE: Steps 2 through 6 required for UPPER WIRING HARNESS replacement.

Step 3. Remove BLACK wires from INTERFACE BOARD (73).

Step 4. Remove BROWN wire from RESET SWITCH (31).

Step 5. Remove LARGE CONNECTOR from INTERFACE BOARD(73),

Step 6. Pull UPPER WIRING HARNESS (64g) from CONSOLE TUBE (40).

Step 7. Remove SMALL CONNECTOR from INTERFACE BOARD (73).

Steps 7 through 12 required for LOWER WIRING HARNESS replacement.

Step 8. Remove GRAY and BLUE wire from MOTOR CONTROLLER (42).

Step 9. Remove REED SWITCH (23) - see REED SWITCH REPLACEMENT.

Step 10. Remove WHITE wires from INTERFACE BOARD (73).

Step 11. Remove WHITE wire from MOTOR CONTROLLER (42).

Step 12. Remove LOWER WIRING HARNESS.

Step 13. Replace WIRING HARNESSES and reinstall in reverse order. Refer to SPEED CONTROL SYSTEM WIRING DIAGRAM to assure proper wiring.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Prime Fit Concourse 10.55 GI Treadmill by pp Contents Display FeaturesTreadmill Operation OperationSlDERAILS \,,iProgrammable Functions OperationFitness Computer Automatically Displayed FunctionsCable Massage Earlobe to increase circulationProng grounded See -Reed Switch Adjustment on Replace MagnetReplace Reed Switch Earclip.- See Using The PulseTroubleshooting Console and Motor SystemMotor To Frame Replace Tachometer Magnet /Replace Fan TroubleshootingTreadmill Will Not Start Verify Wall Outlet Has Replace MotorReplace Interface Board Speed Control System TROUBLE-SHOOTINGSet Speed To 6.0 MPH To BadParts Removal and Replacement Parts ReplacementMotor 35b And Or Flywheel Pulley 35c Replacement Parts ReplacementRemove Console attaching Screws Reset Switch 33 ReplacementIncline Lever 46e Replacement Gas Cylinder 26 ReplacementGAS Cylinder 26 to Incline Brace SlDERAIL REED/J AdjustmentsReattach Motor Cover 43 see Figure 118Packets 1/3oz ea MaintenanceLubricant Order Form Lubrication Schedule09169300 30464516 31294216 34026910 22a AssemblyParts 04043500 30464216 31294116Parts 22e 22f 6955 2622e 35c35a 34b 22i 22b Incline Lever 46r46d 46f 46j 46n 46g 461 46k 46q 46p460 Diversified Products Corporation Box Attn. Customer Service Parts
Top Page Image Contents