Sharp AN-PR1000H operation manual Error indicators and warnings, References, Troubleshooting chart

Page 40

AN-PR1000H

References

Troubleshooting chart (continued)

If trouble occurs

When this product is subjected to strong external interference (mechanical shock, ex- cessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is oper- ated incorrectly, it may malfunction.

If such a problem occurs, do the following:

1Set the unit to the stand-by mode and turn the power on again.

2If the unit is not restored in the previous operation, unplug and plug in the unit, and then turn the power on.

Note:

If neither operation above restores the unit, clear all the memory by resetting it.

Clearing all the memory (reset)

1Unplug the unit.

2Whilst holding down the FUNCTION button, plug in the AC power lead. "RESET" is displayed on the display for about 1 second, the unit is turned off.

3Press the ON/STAND-BY button again to turn the power on.

Caution:

If the unit is reset, each setting returns to default.

When the protection circuit is activated:

If the speaker connection lead is short-circuited, the protection circuit will be activated. When the protection circuit functions, the unit is turned off automatically. At that time, the power indicator blinks red and green alternately.

Unplug the AC power lead and plug it in again after 5 minutes or more. Then check the operation. (*)

Error indicators and warnings

When you fail to perform operations properly, the following messages are displayed on the unit.

Display

Meaning

The cooling fan at the rear of the unit does not run.

Unplug the AC power lead and check if for- eign objects get caught around the cooling fan.

Malfunction of the surround circuit.

Place the unit away from noise source and plug the AC power lead into another wall socket. (*)

Malfunction of circuits other than the sur- round circuit.

Place the unit away from noise source and plug the AC power lead into another wall socket. (*)

When there is no input signal.

Play back the connected equipment.

Nonstandard signal. Cannot be recognised.

Signals other than DOLBY DIGITAL, DTS,

Linear PCM cannot be recognised.

Poor connection of the digital audio input terminal.

Turn off the unit and check if the cable is connected properly.

When the protection circuit of the amplifier is activated.

See left.

Power indicator

(*): Should the same message appear even if the unit is unplugged and plugged in or is set to the stand-by mode and on again, contact your local dealer where you pur- chased the unit.

40

06/3/14

AN-PR1000_EN.fm

TINSEA127AWZZ

Page 39 Page 41
Image 40
Page 39 Page 41
Contents AN-PR1000H Contents AN-PR1000HSpecial NotesAccessories GeneralPrecautions Volume controlGeneral Information GeneralControls and indicators InformationGeneral Main unit front panel Main unit rear panelControls and indicators Display Remote control AN-PR1000HControls and indicators18, 26, 28, 32 Volume Up and Down Buttons ON/STAND-BY button Menu/Top Menu ButtonCursor Buttons Return Button Review/Cue Buttons Play ButtonSystem connections Preparation for UseExternal FM aerial Supplied FM aerialUsing other subwoofer Subwoofer connectionSystem connections For UsePlacing the TV or other equipment Falling prevention Connecting a TV, etc AN-PR1000HAudio connections to TVs, DVD players, VCRs, etcConnecting a DVD player, etc Connecting a VCR, etcAC power connection Connecting a digital tuner, etcConnecting the AC power lead To turn the power onRemote control Battery installationTest of the remote control Close the cover Precautions for battery useAN-PR1000HGeneral control MutingSubwoofer level control To change the display brightness 2 levelsSetting the clock To readjust the clockTo confirm the time display To change the 24-hour or 12-hour displayListening to the playback sound from DVD players, VCRs, etc Remote control operationBasic Operation Enjoying surround sound sound mode Preset sound modes and sound imageEnjoying surround sound sound mode Preset sound modePress the VS button Dolby Virtual Speaker DVS sound modeDolby Virtual Speaker is deactivated Audistry sound mode Press the button for your desired modeDolby Digital DTS Digital Theatre SystemsDolby Pro Logic Tuning AN-PR1000HListening to the radioTo erase entire preset memory RadioMemorising a station To recall a memorised stationAN-PR1000HUsing the Radio Data System RDS Advanced FeaturesYou can control the RDS by using the remote control only Information provided by RDSUsing the Auto Station Programme Memory Aspm To erase all of the contents of preset memoryPress the Tuner button to select the FM stereo band To stop the Aspm operation before it is completeAN-PR1000HUsing the Radio Data System RDS To recall stations in memoryTo specify programme types and select stations PTY search If you select the traffic programmeNews Timer and sleep operation Setting the timerBefore setting timer Set the time to finish as in steps 3 and 4 aboveSetting the sleep timer To use timer and sleep operation togetherTimer and sleep operation To check the timer settingWatching TV Operating the TV or DVD player with the remote controlPlaying a DVD Action Buttons to be Operation procedure Used Operating the TV or DVD player with the remote controlVarious operations of DVD player Changing the manufacturer setting of the remote control To change the TV manufacturer setting To change the DVD player manufacturer setting DVD player setting numberChanging the manufacturer setting of the remote control TV setting numberTroubleshooting chart Symptom Possible causeError indicators and warnings Troubleshooting chartWhen the protection circuit is activated ReferencesSpecifications MaintenanceCleaning the cabinet Memo 1300 135 Warranty
Top Page Image Contents