Sharp AN-PR1000H operation manual Using the Auto Station Programme Memory Aspm

Page 29

Using the Auto Station Programme Memory (ASPM)

Whilst in the ASPM operation mode, the tuner will automatically search for new RDS stations. Up to 40 stations can be stored.

If you have already stored some stations in memory, the number of new stations you can store will be less.

1 Press the TUNER button to select the FM stereo band.

TUNER

ASPM

2 Press the SHIFT button, and then hold down the RDS ASPM button for at least 3 seconds.

TUNER

SHIFT ASPM

1After "ASPM" has flashed for about 4 seconds, scanning will start (87.50 - 108.00 MHz).

2When an RDS station is found, "RDS" will appear for a short time and station will be stored in memory.

3After scanning, the number of stations stored in memory will be displayed for 4 seconds, and then "END" will appear for 4 seconds.

AN-PR1000H

To stop the ASPM operation before it is complete:

 

Press the RDS ASPM button whilst it is scanning for stations.

 

The stations which are already stored in memory will be kept there.

 

Notes:

 

If the same station is broadcasting on different frequencies, the strongest

 

frequency will be stored in memory.

 

Any station which has the same frequency as one stored in memory will not be

 

stored.

 

If 40 stations have already been stored in memory, the scan will be aborted. If you

 

want to redo the ASPM operation, erase the preset memory.

 

If no stations have been stored in memory, "END" will appear for about 4 seconds.

 

If the RDS signals are very weak, station names may not be stored in memory.

Features

To erase all of the contents of preset memory:

 

1 Hold the CLEAR button down for 4 seconds or more.

 

2 Within 10 seconds, press the SHIFT and ENTER buttons.

 

After performing this operation, all of the preset memory information will be erased.

 

To store a station name again if the wrong name was stored in memory:

 

It may be impossible to store station names in memory using the ASPM function if

 

there is lots of noise or if the signal is too weak. In this case, perform as follows.

 

1 Hold down the SHIFT button and press the PRESET (

 

or

 

) button to check

Advanced

 

 

 

 

In a certain area or during certain time periods, the station names may temporarily

whether the names are correct.

 

2 If you find a wrong name during receiving the station, wait until the correct name

 

will be displayed and then press the SHIFT and ENTER buttons.

 

3 Within 5 seconds, press the SHIFT and ENTER buttons whilst the preset channel

 

number is flashing.

 

The new station name has been stored in memory correctly.

 

Notes:

 

The same station name can be stored in different channels.

 

be different.

 

Notes for RDS operation

 

If any of the following events occur, it does not mean that the unit is

 

faulty:

 

"PS", "NO PS" and a station name appear alternately, and the unit does not operate

 

properly.

 

If a particular station is not broadcasting properly or a station is conducting tests,

 

the RDS reception function may not work properly.

 

When you receive an RDS station whose signal is too weak, information like the

 

station name may not be displayed.

 

"NO PS" or "NO PTY" will flash for about 5 seconds, and then the frequency will be

 

displayed.

 

 

 

 

 

 

 

 

 

 

 

 

29

1

2

3

4

5

6

7

8

06/3/14

AN-PR1000_EN.fm

TINSEA127AWZZ

Page 28 Page 30
Image 29
Page 28 Page 30
Contents AN-PR1000H AN-PR1000HSpecial Notes ContentsGeneral AccessoriesVolume control PrecautionsGeneral Information GeneralInformation Controls and indicatorsGeneral Main unit front panel Main unit rear panelControls and indicators Display 18, 26, 28, 32 AN-PR1000HControls and indicatorsRemote control ON/STAND-BY button Menu/Top Menu Button Volume Up and Down ButtonsCursor Buttons Return Button Review/Cue Buttons Play ButtonPreparation for Use System connectionsExternal FM aerial Supplied FM aerialSubwoofer connection Using other subwooferPlacing the TV or other equipment For UseSystem connections Falling prevention AN-PR1000HAudio connections to TVs, DVD players, VCRs, etc Connecting a TV, etcConnecting a VCR, etc Connecting a DVD player, etcConnecting a digital tuner, etc AC power connectionConnecting the AC power lead To turn the power onBattery installation Remote controlTest of the remote control Close the cover Precautions for battery useMuting AN-PR1000HGeneral controlSubwoofer level control To change the display brightness 2 levelsTo readjust the clock Setting the clockTo confirm the time display To change the 24-hour or 12-hour displayBasic Operation Remote control operationListening to the playback sound from DVD players, VCRs, etc Preset sound modes and sound image Enjoying surround sound sound modePreset sound mode Enjoying surround sound sound modeDolby Virtual Speaker is deactivated Dolby Virtual Speaker DVS sound modePress the VS button Press the button for your desired mode Audistry sound modeDolby Pro Logic DTS Digital Theatre SystemsDolby Digital AN-PR1000HListening to the radio TuningRadio To erase entire preset memoryMemorising a station To recall a memorised stationAdvanced Features AN-PR1000HUsing the Radio Data System RDSYou can control the RDS by using the remote control only Information provided by RDSTo erase all of the contents of preset memory Using the Auto Station Programme Memory AspmPress the Tuner button to select the FM stereo band To stop the Aspm operation before it is completeTo recall stations in memory AN-PR1000HUsing the Radio Data System RDSTo specify programme types and select stations PTY search If you select the traffic programmeNews Setting the timer Timer and sleep operationBefore setting timer Set the time to finish as in steps 3 and 4 aboveTo use timer and sleep operation together Setting the sleep timerTo check the timer setting Timer and sleep operationPlaying a DVD Operating the TV or DVD player with the remote controlWatching TV Various operations of DVD player Operating the TV or DVD player with the remote controlAction Buttons to be Operation procedure Used To change the TV manufacturer setting Changing the manufacturer setting of the remote controlTo change the DVD player manufacturer setting DVD player setting numberTV setting number Changing the manufacturer setting of the remote controlSymptom Possible cause Troubleshooting chartTroubleshooting chart Error indicators and warningsWhen the protection circuit is activated ReferencesCleaning the cabinet MaintenanceSpecifications Memo 1300 135 Warranty

AN-PR1000H specifications

The Sharp AN-PR1000H is an advanced air purifier that combines innovative technology and user-centric features to deliver exceptional indoor air quality. Designed for households and offices, this model stands out with its sleek design and effective performance, making it an appealing choice for those looking to improve their environment.

One of the key features of the AN-PR1000H is its powerful air filtration system. It employs a multi-layer filtration process that includes a pre-filter, activated carbon filter, and a high-performance HEPA filter. The HEPA filter captures up to 99.97% of airborne particles as small as 0.3 microns, including dust, pollen, and pet dander. The activated carbon filter effectively neutralizes odors and volatile organic compounds (VOCs), ensuring that the air you breathe is not only clean but also fresh.

Incorporating Sharp's exclusive Plasmacluster technology, the AN-PR1000H emits positive and negative ions into the air. This technology helps to reduce allergens, mold, and bacteria, contributing to a healthier living space. The ions attach to airborne particles, causing them to clump together and fall out of the air, making it easier for the filters to capture them.

The AN-PR1000H is designed with user convenience in mind. It features an intuitive control panel that allows users to adjust settings with ease. With multiple fan speed options and an automatic mode that adjusts airflow based on air quality, this air purifier caters to different needs and preferences. A built-in air quality sensor monitors the environment and provides real-time feedback, allowing users to be informed about the air quality in their space.

Another noteworthy aspect of the AN-PR1000H is its quiet operation. The unit runs quietly, making it perfect for use in bedrooms, nurseries, and offices where noise levels need to be kept to a minimum. Its compact design allows for easy placement in various settings without taking up too much space.

For added convenience, the AN-PR1000H features a filter replacement indicator that alerts users when it's time to change the filters, ensuring optimal performance at all times. With a stylish design, advanced filtration technology, and user-friendly features, the Sharp AN-PR1000H is an excellent choice for anyone looking to enhance their indoor air quality and overall well-being.
Top Page Image Contents