JVC FS-X5 Adjusting the Brightness Dimmer at Power On, Power Saving Mode Dimmer at Power Off

Page 13

Basic Operations

English

Adjusting the Brightness (DIMMER - at Power On)

You can adjust the brightness of the display.

When the System is Turned On

At power on, each time you press the DIMMER button on the Remote Control, the brightness changes as follows: DIMMER OFF = DIMMER 1 = DIMMER 2 = (back to the beginning)

DIMMER OFF : Bright

DIMMER 1 : Dark (CD lamp also becomes dark.)

DIMMER 2 : Darker (CD lamp goes out.)

Power Saving Mode (DIMMER - at Power Off)

In power saving mode, you can save the power while the System is turned off (Standby Mode).

Each time you press the DIMMER button on the Remote Control at power off, the display alternates as follows.

DISPLAY ON Ô DISPLAY OFF

To enable Power Saving mode, set to “DISPLAY OFF”.

The display completely turns off to save the power.

To restore normal power mode, reset to “DISPLAY ON”. The Clock indicator () and the clock appear on the display.

Adjusting the Volume

Turn the VOLUME control on the Unit clockwise to in- crease the volume or turn it counterclockwise to decrease the volume.

Press the VOLUME + button on the Remote Control to in- crease the volume or press the VOLUME _ button on the Remote Control to decrease the volume.

You can adjust the volume level between 0 and 50.

For private listening

Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers.

Be sure to turn down the volume before connecting or put- ting on headphones.

CAUTION:

•DO NOT turn off the System with the volu- me set to an extremely high level; otherwi- se a sudden blast of sound could damage your hearing, speakers and/or headphones when you turn on the System or start play- ing any source next time.

REMEMBER you cannot adjust the volume level while the System is in standby mode.

Fade-out Muting (FADE MUTING)

You can mute the output with one touch operation.

To mute the output, press the FADE MUTING button on the Remote Control. Then, “FADE MUTING” blinks and the output will be faded out and becomes 0.

To release muting, press the FADE MUTING button once again. Then, the output will be faded in to the original level.

•Adjusting the volume causes the muting process (fading out to 0) to release.

•If you use the AHB PRO button or the BASS/TREBLE but- ton during muting, the FADE MUTING button does not

work to release muting. In this case, turn the VOLUME control on the Unit or the VOLUME+/ _ button on the Re- mote Control to newly set the volume.

Reinforcing the Bass Sound (Active Hyper Bass Pro.)

You can reinforce the bass sound to maintain rich, full bass at low volume. (This effect does not apply to the headphones.)

To get the effect, press the AHB PRO button on the Unit or the Remote Control.

“AHB PRO ON” appears and the “BASS” indicator lights up. To cancel the effect, press the AHB PRO button again. “AHB PRO OFF” appears and the “BASS” indicator goes out.

9

Page 12 Page 14
Image 13
Page 12 Page 14
Contents FS-X5 For U.S.A Mises en garde, précautions et indications diversesFor Canada/pour le Canada Disconnect the main plug to shut the power off completelyFront view Face Table of Contents Introduction FeaturesHow This Manual Is Organized How To Put Batteries In the Remote Control AccessoriesUsing the Remote Control Getting StartedUsing the Supplied Wire Antenna Connecting the FM AntennaUsing the Coaxial Type Connector Not Supplied Connecting the AM Antenna Connecting the Speakers SP-FSX5 Connecting an MD Recorder, etc Optical Digital Output Connecting an External EquipmentAutomatic Power On Basic Operations Turning the Power On and OffChanging the Source Power Saving Mode Dimmer at Power Off Adjusting the Brightness Dimmer at Power OnAdjusting the Volume Fade-out Muting Fade MutingTo disable the A.P.off function No signal conditionAuto Power Off A.P.off Entering the Number with the Remote Control Numeric KeysTuning In a Station Using the TunerSelect a station using one of the follow- ing methods One Touch RadioTo Change the FM Reception Mode Presetting StationsTo change the preset stations, repeat the same Beat Cut AM ReceptionWhen playing a CD-R or CD-RW Using the CD PlayerTo Insert a CD ControlTo Unload a CD Basics of Using the CD Player Normal PlayProgramming the Playing Order of the Tracks Program Play To Modify the Program Press the CD 6button on the Remote ControlRandom Play Repeat to program the other tracksLocking the CD door Repeating TracksUnlocking the CD door Turn off the systemListening to External Equipment Using External EquipmentsChanging the Equipment’s Name To exit the source LINE, select other source e.g. CDRecording the System’s Source to External Equipment Adjusting the Input LevelSetting the Clock Using the TimersPress the CLOCK/TIMER button Press the 3 or 2 button to set the hourPerform steps 2 to 5 in Setting the Clo- ck on Setting the Daily TimerShowing the Clock Display Correcting the ClockSetting the OFF time Example PM Setting the on time Example AMSelecting the music source Setting the volume level Turning the Daily Timer On and OffPress the Cancel button Select the Fade functionTimer Priority Setting the Sleep TimerDuring playback a source, press the Sleep button Wait for a few secondsSymptom TroubleshootingPossible Cause ActionCare And Maintenance Specifications Caractéristiques
Top Page Image Contents