JVC FS-X5 manual Presetting Stations, To Change the FM Reception Mode, Beat Cut AM Reception

Page 16

English

Using the Tuner

Presetting Stations

You can preset up to 30 FM stations and up to 15 AM sta- tions.

Preset numbers may have been set to factory test fre- quencies prior to shipment. This is not a malfunction. You can preset the stations you want into memory by following one of the presetting methods below.

1

 

 

STORED

FM/AM

 

 

 

SET

+10

2

SET

or

FM = 30, AM = 15

When changing the Band

On the Remote Control

1 Select a band by pressing the FM/AM button.

2 Press the 5 or button to tune in a sta- tion.

3 Press the SET button.

Preset number “1” will blink for 5 seconds. Within 5 seconds, proceed to the next step.

When the display returns to the one set in step 2 after 5 seconds, press the SET button again.

CAUTION:

Even if the system is unplugged or if the power failure occurs, the preset stations will be stored for about 24 hours. However, in case the preset stations are erased, you will need to preset the stations again.

To Change the FM Reception Mode

When you are tuned into an FM stereo broadcast, the “ST.” indicator lights up and you can hear stereo effects.

If an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose stereo effect.

FM AUTO mode is also useful to suppress static noise be- tween stations.

To enter Monaural mode while receiving an FM broadcast, press the FM/PLAY MODE button on the Re- mote Control until “FM MONO” appears on the display. Then, the “MONO” indicator lights up.

Each time you press the FM/PLAY MODE button, the display alternates between “FM AUTO” and “FM MONO”.

FM/PLAY

MODE

FM AUTO Ô FM MONO

To restore the stereo effect, press the FM/PLAY MODE button on the Remote Control until “FM AUTO” ap- pears on the display. Then, the “MONO” indicator goes out and the “ST.” indicator will light up.

4 Press the Numeric Keys, or the 3 or 2 button within 5 seconds to select the preset number.

Example:

5 Press the SET button within 5 seconds.

“STORED” appears and after 2 seconds, the display re- turns to the broadcast frequency display.

6 Repeat above steps 1 to 5 for each sta- tion you want to store in memory with a preset number.

To change the preset stations, repeat the same

steps as above.

Beat Cut (AM Reception)

Switching the Beat Cut mode may reduce beat noise.

Each time you press the FM/PLAY MODE button while re- ceiving an AM broadcast, the Beat Cut mode changes as fol- lows.

BEAT CUT 1 = BEAT CUT 2 = BEAT CUT 3 = BEAT CUT 4 = (back to the beginning)

FM/PLAY

MODE

Set to the position where beat noise is small.

The best position will differ depending on the AM broadcast station being received.

In AM broadcast, reception sensitivity will be changed by turning the AM loop antenna. Turn the AM loop antenna for best reception.

12

Image 16
Contents FS-X5 Mises en garde, précautions et indications diverses For U.S.ADisconnect the main plug to shut the power off completely For Canada/pour le CanadaFront view Face Table of Contents Introduction FeaturesHow This Manual Is Organized Accessories How To Put Batteries In the Remote ControlUsing the Remote Control Getting StartedUsing the Supplied Wire Antenna Connecting the FM AntennaUsing the Coaxial Type Connector Not Supplied Connecting the AM Antenna Connecting the Speakers SP-FSX5 Connecting an MD Recorder, etc Optical Digital Output Connecting an External EquipmentAutomatic Power On Basic Operations Turning the Power On and OffChanging the Source Adjusting the Brightness Dimmer at Power On Power Saving Mode Dimmer at Power OffAdjusting the Volume Fade-out Muting Fade MutingNo signal condition To disable the A.P.off functionAuto Power Off A.P.off Entering the Number with the Remote Control Numeric KeysUsing the Tuner Tuning In a StationSelect a station using one of the follow- ing methods One Touch RadioPresetting Stations To Change the FM Reception ModeTo change the preset stations, repeat the same Beat Cut AM ReceptionUsing the CD Player When playing a CD-R or CD-RWTo Insert a CD ControlTo Unload a CD Basics of Using the CD Player Normal PlayProgramming the Playing Order of the Tracks Program Play Press the CD 6button on the Remote Control To Modify the ProgramRandom Play Repeat to program the other tracksRepeating Tracks Locking the CD doorUnlocking the CD door Turn off the systemUsing External Equipments Listening to External EquipmentChanging the Equipment’s Name To exit the source LINE, select other source e.g. CDAdjusting the Input Level Recording the System’s Source to External EquipmentUsing the Timers Setting the ClockPress the CLOCK/TIMER button Press the 3 or 2 button to set the hourSetting the Daily Timer Perform steps 2 to 5 in Setting the Clo- ck onShowing the Clock Display Correcting the ClockSetting the OFF time Example PM Setting the on time Example AMSelecting the music source Turning the Daily Timer On and Off Setting the volume levelPress the Cancel button Select the Fade functionSetting the Sleep Timer Timer PriorityDuring playback a source, press the Sleep button Wait for a few secondsTroubleshooting SymptomPossible Cause ActionCare And Maintenance Specifications Caractéristiques