JVC FS-X5 manual Tone Control BASS/TREBLE, No signal condition, To disable the A.P.off function

Page 14

English

Basic Operations

Tone Control (BASS/TREBLE)

You can control the tone by changing the bass (low frequen- cy) and treble (high frequency).

On the Remote Control

1 Press the BASS/TREBLE button.

Each time you press the button, the Tone Control mode changes as follows.

BASS = TREBLE = Normal display = (back to the begin- ning)

No signal condition:

Source CD: CD is stopped or no CD is inserted.

When no signal condition continues, “A.P.off 20 sec” (20 seconds left before elapsed time reaches three minutes) ap- pears on the display. The displayed time is counted down and, finally, the System is turned off (Standby mode).

•If a CD is played back, the “A.P.off” indicator stops blinking and stays lit again.

•If you press a button or turn the VOLUME control, three-minute counting down is reset and counting down newly restarts.

To disable the A.P.off function

2 While “BASS” or “TREBLE” appears on

When the source is “CD”, press the A.P.off button on the

the display, press the VOLUME + or -

Remote Control until “A.P.off STOP” appears on the dis-

button to adjust the bass or treble level.

play.

Then, the “A.P.off” indicator goes out.

You can change the level within the range of -5 to +5. (0: flat)

 

 

 

3 Press the BASS/TREBLE button until normal display appears.

Waiting for five seconds will also return the System to the normal display.

Auto Power Off (A.P.off)

You can automatically turn off the System when no signal condition continues for three minutes. This function is ef- fective when the source is set to “CD”, but not to “FM”, “AM” or “LINE”.

Entering the Number with the Remote Control (Numeric Keys)

You will use the Numeric Keys on the Remote Control to enter numbers for presetting stations, recalling the preset stations, selecting track number, or programming the play- ing tracks on a CD.

How to enter the number with the Numeric Keys is ex- plained here.

Examples:

•To enter number 5, press 5.

•To enter number 10, press 10.

•To enter number 15, press +10 then 5.

•To enter number 20, press +10 then 10.

•To enter number 25, press +10, +10, then 5.

To Enable the A.P.off function (When the source is “CD”)

1 Press the A.P.off button on the Remote Control until “A.P.off SET” appears on the display.

Then, the “A.P.off” indicator lights up on the display.

•Each time you press the button, the display alternates as follows.

A.P.off SET Ô A.P.off STOP

When no signal condition is detected, the “A.P.off” indica- tor will start blinking soon.

10

Page 13 Page 15
Image 14
Page 13 Page 15
Contents FS-X5 Mises en garde, précautions et indications diverses For U.S.ADisconnect the main plug to shut the power off completely For Canada/pour le CanadaFront view Face Table of Contents How This Manual Is Organized FeaturesIntroduction Using the Remote Control AccessoriesHow To Put Batteries In the Remote Control Getting StartedUsing the Coaxial Type Connector Not Supplied Connecting the FM AntennaUsing the Supplied Wire Antenna Connecting the AM Antenna Connecting the Speakers SP-FSX5 Automatic Power On Connecting an External EquipmentConnecting an MD Recorder, etc Optical Digital Output Changing the Source Turning the Power On and OffBasic Operations Adjusting the Volume Adjusting the Brightness Dimmer at Power OnPower Saving Mode Dimmer at Power Off Fade-out Muting Fade MutingAuto Power Off A.P.off No signal conditionTo disable the A.P.off function Entering the Number with the Remote Control Numeric KeysSelect a station using one of the follow- ing methods Using the TunerTuning In a Station One Touch RadioTo change the preset stations, repeat the same Presetting StationsTo Change the FM Reception Mode Beat Cut AM ReceptionTo Insert a CD Using the CD PlayerWhen playing a CD-R or CD-RW ControlProgramming the Playing Order of the Tracks Program Play Basics of Using the CD Player Normal PlayTo Unload a CD Random Play Press the CD 6button on the Remote ControlTo Modify the Program Repeat to program the other tracksUnlocking the CD door Repeating TracksLocking the CD door Turn off the systemChanging the Equipment’s Name Using External EquipmentsListening to External Equipment To exit the source LINE, select other source e.g. CDAdjusting the Input Level Recording the System’s Source to External EquipmentPress the CLOCK/TIMER button Using the TimersSetting the Clock Press the 3 or 2 button to set the hourShowing the Clock Display Setting the Daily TimerPerform steps 2 to 5 in Setting the Clo- ck on Correcting the ClockSelecting the music source Setting the on time Example AMSetting the OFF time Example PM Press the Cancel button Turning the Daily Timer On and OffSetting the volume level Select the Fade functionDuring playback a source, press the Sleep button Setting the Sleep TimerTimer Priority Wait for a few secondsPossible Cause TroubleshootingSymptom ActionCare And Maintenance Specifications Caractéristiques
Top Page Image Contents