NordicTrack NTL06907.0 user manual Problem The walking belt slows when walked on

Page 27

Locate the Reed Switch (71) and the Magnet (50) on the left side of the Pulley (51). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in (3 mm). If neces- sary, loosen the 3/4" Reed Switch Screw (15), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood, and run the tread- mill for a few minutes to check for a correct speed reading.

1/8 in.

15

50

71

51

Top

View

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE INFORMATION MODE on page 23 to turn off the demo mode.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 8 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

2–3 in.

 

Rear Roller Bolts

c. If the walking belt still slows when walked on, see the back cover of this manual.

27

Image 27
Contents QUESTIONS? Model No. NTL06907.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin For your benefit, read this manual carefully beforeBack Right Side Do not fully fold the Frame yet AssemblyMake sure that the power cord is unplugged Be includedFully tighten the Bolts yet Careful not to pinch the Upright WireRounded Not Connected PROPERLY, the CON Sole MAY be Damaged When Power is Turned onRaise the Frame 56 to the position shown Small Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to Turn on the Power HOW to Personalize Console SettingsSelect the user mode Select a default user setting HOW to Identify Yourself AS User 1 or UserSet the date and time HOW to USE the Manual Mode HOW to USE a Preset Workout or a Weight Loss Workout Press the Start button to start the workout HOW to Create a Learn Workout HOW to USE a Learn Workout Change the workout if desired HOW to View the Fitness Journal Information Mode HOW to Reset the Fitness JournalSelect the user mode. See on Reset the fitness journal Exit the user modeHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description R1007ADescription Qty Exploded Drawing A-Model No. NTL06907.0 Exploded Drawing B-Model No. NTL06907.0 Exploded Drawing C-Model No. NTL06907.0 Exploded Drawing D-Model No. NTL06907.0 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT