NordicTrack NTL06907.0 user manual Rounded

Page 8

5.With the help of a second person, carefully tip the treadmill onto its right side. Partially fold the Frame (56) so the treadmill is more stable; do not fully fold the Frame yet.

Remove and discard the two indicated bolts (A) and the shipping bracket (B).

Attach a Base Pad (81) to the Base (83) in the location shown with a 1" Tek Screw (2) and a Base Pad Spacer (13). Then, attach another Base Pad (81) with only a 1" Tek Screw (2).

Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4), and the shipping bracket (C) from the Base (83). Attach a Wheel (84) with the Bolt and the Nut that you just removed. Do not overtighten the Nut; the Wheel must turn freely. Discard the shipping bracket.

6.With the help of a second person, hold a Bolt Spacer (80) inside the lower end of the Left Upright (74). Insert a 3/8" x 4 1/2" Bolt (6) with a 3/8" Star Washer (9) into the Left Upright and the Bolt Spacer. Repeat this step with a second Bolt Spacer (80), 3/8" x 4 1/2" Bolt (6), and 3/8" Star Washer (9).

Orient the Left Upright (74) and the Left Upright Spacer (76) as shown. Hold the Left Upright Spacer and the Left Upright against the Base (83). Finger tighten the two 3/8" x 4 1/2" Bolts (6); do not fully tighten the Bolts yet.

Press a Base Endcap (77) into Base (83).

With the help of a second person, tip the tread- mill so that the Base (83) is flat on the floor.

7.Have a second person hold the Bridge (95) near the Right Upright (78). Remove the wire tie from the Upright Wire (38).

Connect the Upright Wire (38) to the Bridge Wire (52). Make sure to connect the connectors properly (see the inset drawing). The connec- tors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT

CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

5

B

 

 

A

 

 

 

 

 

 

83

 

81

 

56

 

2

 

 

4

 

 

 

 

13

 

 

 

 

84

 

 

2

81

 

 

 

8

C

6

 

 

 

6

 

74

 

9

 

 

 

 

76

 

 

80

 

Rounded

 

 

Corner

 

80

 

 

 

77

83

 

 

7

95

 

 

 

 

 

 

52

 

 

 

38

 

 

 

 

78

 

Wire Tie

52

38

8

Image 8
Contents Call TOLL-FREE QUESTIONS?Model No. NTL06907.0 Serial No Table of Contents Important Precautions Page Back Right Side Before YOU BeginFor your benefit, read this manual carefully before Assembly Make sure that the power cord is unpluggedBe included Do not fully fold the Frame yetCareful not to pinch the Upright Wire Fully tighten the Bolts yetRounded Sole MAY be Damaged When Power is Turned on Not Connected PROPERLY, the CONRaise the Frame 56 to the position shown Small PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleSelect the user mode HOW to Turn on the PowerHOW to Personalize Console Settings Set the date and time Select a default user settingHOW to Identify Yourself AS User 1 or User HOW to USE the Manual Mode HOW to USE a Preset Workout or a Weight Loss Workout Press the Start button to start the workout HOW to Create a Learn Workout HOW to USE a Learn Workout Change the workout if desired HOW to View the Fitness Journal HOW to Reset the Fitness Journal Select the user mode. See on Reset the fitness journalExit the user mode Information ModeHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Page Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyR1007A Key No. Qty DescriptionDescription Qty Exploded Drawing A-Model No. NTL06907.0 Exploded Drawing B-Model No. NTL06907.0 Exploded Drawing C-Model No. NTL06907.0 Exploded Drawing D-Model No. NTL06907.0 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty