NordicTrack NTL15907.0 user manual Troubleshooting, Problem The power turns off during use, Top

Page 23

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 10. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch pro- trudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch to the reset position.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch to the reset position.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. If the treadmill still will not run, see the front cover of this manual.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and unplug the power cord. Carefully tip the treadmill down as shown in drawing a. Remove the Screws (87) from the Motor Hood (33). Raise the Upright (20) and care- fully remove the Motor Hood.

Locate the Reed Switch (22) and the Magnet (18) on the left side of the Pulley (17). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Screw (87), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (33) with the Screws (87). Run the treadmill for a few minutes to check for a correct speed reading.

a

 

 

20

87

87

 

33

1/8”

17

87

 

22

18

Top

 

View

 

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Call TOLL-FREE QUESTIONS?Model No. NTL15907.0 Serial No Table of Contents Important Precautions Page Before YOU Begin Assembly Handrail Bolts before tightening them Page Page PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerPage Whenkey. you are finished exercising, remove Turn on the fan if desiredCrease button to start the program HOW to USE a Preset ProgramSelect one of the preset programs Select one of the custom programs When you are finished using the treadmillHOW to Create a Custom Program Follow your progress with the matrix DisplaysFollow your progress with the matrix and the displays HOW to USE a Custom ProgramInsert an iFIT Card and select a program HOW to USE AN Ifit CardUSER’S Mode Optional Chest Pulse Sensor HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Top TroubleshootingProblem The power turns off during use Problem The walking belt slows when walked on Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesQty Description R0207AOrdering Replacement Parts Exploded Drawing A-Model No. NTL15907.0 Exploded Drawing B-Model No. NTL15907.0 Exploded Drawing C-Model No. NTL15907.0 Exploded Drawing D-Model No. NTL15907.0 Limited Warranty
Top Page Image Contents