NordicTrack NTL15909.3 warranty Troubleshooting, Not compatible with GFCI-equipped outlets

Page 22

TROUBLESHOOTING

Most incline trainer problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 14). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 14. IMPORTANT: The incline trainer is

not compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the power switch located on the incline

c

 

trainer frame near the power cord. If the switch pro-

 

trudes as shown, the switch has tripped. To reset

Tripped

Reset

the switch, wait for five minutes and then press the

switch back in.

 

 

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key into the console.

d. If the incline trainer still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the incline trainer is displayed

in a store. If the displays remain lit when you remove the key, the demo mode is turned on. To

turn off the demo mode, hold down the Stop button for a few seconds. If the displays are still lit,

see THE INFORMATION MODE on page 20 to turn off the demo mode.

 

PROBLEM: The displays of the console do not function properly

 

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

 

POWER CORD. Next, remove the three indicated #8

 

x 1/2" Cover Screws (18). Then, lift off the Left Roller

 

38

Cover (38).

 

 

18

18

 

 

23

Image 22
Contents QUESTIONS? Serial NoTable of Contents Use of this product Important PrecautionsHandrails while using the incline trainer Before beginning this or any exercise proIncline trainer is intended for in-home use Serial Number Before YOU BeginDecal Assembly Upright Wire 78. See the upper inset draw Make sure that the power cord is unpluggedSee the lower inset drawing. Tie the wire tie Tighten each of them. Be careful not to pinch Upright WireScrews for step Page 102 Ties Hole Wires Console Wire Ties Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the Console HOW to USE the Manual Mode Measure your heart rate if desired Change the incline of the incline trainer as desiredMonitor your progress with the display Turn on the fan if desiredHOW to USE a Calorie Workout Start the workoutHOW to USE a Random Workout Information Mode MetricHOW to USE the Stereo Sound System HOW to USE the Ifit Training ModeHOW to Move the Incline Trainer Problem The power turns off during use TroubleshootingNot compatible with GFCI-equipped outlets Problem The walking belt slows when walked on TopProblem The console display has lines running through it Unplug the Power CORD. If the walking beltKey and Unplug the Power CORD. Using Ing belt has shifted to the right, turn the bolt counWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. NTL15909.3 Key No. Qty DescriptionQty R0910A Exploded Drawing B-Model No. NTL15909.3 Exploded Drawing C-Model No. NTL15909.3 Exploded Drawing D-Model No. NTL15909.3 Ordering Replacement Parts Limited Warranty Icon Health & Fitness, Inc., 1500 S W., Logan, UTPart No R0910A