Reebok Fitness RBTL09906.0 manual Assembly, Make sure that the power cord is unplugged

Page 6

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed.

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex key and your own phillips screwdriver

.

For help identifying the assembly hardware, see the drawings below. The number in parentheses below each drawing is the key number of the part, from the PART LIST on page 30. The number following the parentheses is the quantity needed for assembly. Note: Some small parts may have been pre-assembled. If a part is not in the parts bag, check to see if it has been pre-assembled. To avoid damaging plastic parts, do not use power tools for assembly.

Extension Leg Nut (67)–4

Star Washer (8)–4

1” Tek Screw (83)–4

Screw (3)–2

Console Bolt (64)–4

Extension Leg Bolt (65)–4

1. Make sure that the power cord is unplugged.

1

 

 

 

With the help of a second person, carefully tip

 

84

the treadmill onto its left side as shown. Partially

 

 

 

fold the Frame (58) so the treadmill is more sta-

 

 

ble. Do not fully fold the treadmill until it is

65

82

completely assembled.

82

Attach two Base Pads (82) to the base of the

 

 

Uprights (84) with two 1” Tek Screws (83) as

 

83

shown.

 

 

 

Insert an Extension Leg (89) into the base of the

 

67

Uprights (84) as shown. Hold two Extension Leg

 

89

 

Nuts (67) in the bottom of the Extension Leg.

 

 

 

Next, insert two Extension Leg Bolts (65) into the

58

 

top of the Extension Leg, and firmly tighten the

 

 

 

Extension Leg Bolts into the Extension Leg Nuts.

 

 

 

6

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents
Call TOLL-FREE QUESTIONS?Model No. RBTL09906.0 Serial No Mon.-Fri., 6 a.m.-6 p.m. MST Table of Contents Important Precautions Page Before YOU Begin Right SideBack Assembly Make sure that the power cord is unpluggedPage Bolts and then firmly tighten them Small Cylinder Wire HOW to Connect AN Antenna HOW to Connect a 75 OHM Catv CableHOW to Connect a VCR Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeMeasure your heart rate if desired Turn on the fan if desiredHOW to USE a Preset Program Select a preset programFollow your progress with the displays HOW to USE a Heart Rate Program Put on the chest pulse sensorSelect a heart rate program Follow your progress with the displays HOW to Create a Custom Program Select a custom programHOW to USE a Custom Program HOW to USE the Information Mode HOW to Operate the Personal TelevisionPress the Volume VOL. buttons to adjust Turn on the televisionPress the On/Off button again and add or Delete channels Optional Chest Pulse SensorHOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on Top Problem Television reception is poor Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches R1206A Qty DescriptionDescription Exploded Drawing A-Model No. RBTL09906.0 R1206A Exploded Drawing B-Model No. RBTL09906.0 R1206A Exploded Drawing C-Model No. RBTL09906.0 R1206A Exploded Drawing D-Model No. RBTL09906.0 R1206A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents