Reebok Fitness RBTL09507.0 manual Problem The walking belt slows when walked on

Page 27

b. Remove the three #8 x 3/4" Screws (1) and care- fully pivot the Hood (61) off.

b

1

61

Locate the Reed Switch (71) and the Magnet (50) on the left side of the Pulley (51). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If nec- essary, loosen the 3/4" Reed Switch Screw (15), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown). Run the treadmill for a few minutes to check for a cor- rect speed reading.

1/8 in.

15

50

71

51

Top

View

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

b

2–3 in.

 

Rear Roller Bolts

c. If the walking belt still slows when walked on, see the front cover of this manual.

27

Image 27
Contents On the WEB QUESTIONS?Please do not Contact Call TOLL-FREETable of Contents Important Precautions Page Before YOU Begin Hardware may be included AssemblyWheel must turn freely Make sure that the power cord is unpluggedBe careful not to pinch the Upright Wire Gers do not fully tighten the Bolts yetNot fully fold the Frame yet Not Connected PROPERLY, the CON Tor and try again. if the Connectors areSole MAY be Damaged When Power is Turned on Not to pinch the wiresBolts See steps 4 and 6. Tighten the 3/8 x 4 1/2Small Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramInsert the key into the console HOW to Turn on the PowerHOW to Personalize Console Settings Select the user modeSelect a default user setting HOW to Identify Yourself AS User 1 or UserSet the date and time Start the walking belt and adjust the speed HOW to USE the Manual ModePersonalize console settings if desired Select the manual modeMeasure your heart rate if desired HOW to USE a Classic Workout Select a preset classic workoutPress the Start button to start the workout Select an event training workout HOW to USE AN Event Training WorkoutSelect one of the four custom workouts HOW to Create a Custom WorkoutHOW to USE a Custom Workout HOW to View the Fitness Journal Information Mode HOW to Reset the Fitness JournalSelect the user mode. See on Reset the fitness journal Exit the user modeOptional Chest Pulse Sensor HOW to USE the Stereo Sound SystemHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description R1107AQty Exploded Drawing A-Model No. RBTL09507.0 R1107A Exploded Drawing B-Model No. RBTL09507.0 R1107A Exploded Drawing C-Model No. RBTL09507.0 Exploded Drawing D-Model No. RBTL09507.0 R1107A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT