Triumph Plant 700T manual Centering the Running Belt

Page 13

INTRODUCTION IMPORTANT PRECAUTIONS

ASSEMBLY

BEFORE YOU BEGIN

TREADMILL OPERATION

CONDITIONING TROUBLESHOOTING GUIDELINES & MAINTENANCE

TENSIONING­THE RUNNING BELT

The running belt has been properly adjusted at the factory before it was shipped. At times the belt can move off-center during shipment.

CAUTION: Running belt should NOT be moving during tensioning. Over-tightening the running belt can cause excessive wear on the treadmill as well as its components. Never over-tighten the belt.

If you can feel a slipping sensation when running on the treadmill, the running belt must be tightened. In most cases, the belt has stretched from use, causing the belt to slip. This is a normal and common adjustment. To eliminate this slipping, TURN THE TREADMILL OFF and tension both the rear roller bolts using the supplied Allen wrench, turning them 1/4 TURN to the right as shown. Turn the treadmill on and check for slipping. Repeat if necessary, but NEVER TURN the roller bolts more than 1/4 turn at a time. Belt is properly tensioned when the slipping sensation is gone.

Belt is too far to the right side

Belt is too far to the left side

CENTERING THE RUNNING BELT

The running belt has been properly adjusted at the factory before it was shipped. At times the belt can move off-center during shipment. Before operating the treadmill, make sure the belt is centered and remains centered to maintain smooth operation.

CAUTION: Do not run belt faster than 1/2 mph while centering. Keep fingers, hair and clothing away from belt at all times.

If the running belt is too far to the right side:

With the treadmill running at 1/2 mph, turn the right adjustment bolt clockwise 1/4 turn at a time (using the supplied Allen wrench). Check the belt alignment. Allow belt to run a full cycle to gauge if more adjustment is needed. Repeat if necessary, until the belt remains centered during use.

If the running belt is too far to the left side:

With the treadmill running at 1/2 mph, turn the right adjustment bolt counter-clockwise 1/4 turn at a time (using the supplied Allen wrench). Check the belt alignment. Allow belt to run a full cycle to gauge if more adjustment is needed. Repeat if necessary, until the belt remains centered during use.

LIMITED WARRANTY

14

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Treadmill USER’S Guide T R O D U C T I O N Table of ContentsGrounding Instructions Important PrecautionsUse the treadmill only as described in this manual OperationUnpacking S E M B LYTools Included Repeat on the other side Open Hardware BAGIntroduction Hardware BAG 2 Contents To avoid damage. Note Do not Into each otherOpen Hardware BAG Fold up the deck Before YOU Begin Safety KEYLocation of the Treadmill Here are just a few of the health benefits of exerciseFolding Proper UsageMoving Centering the Running Belt JAI Treadmill OperationMonitor Display Hand grip sensors How to USESelect a PROgram To Reset ConsoleQuick KEY Operation Finishing Your WorkoutProgram Profiles Weight Loss Speed ChangesIntervals Speed Changes Rolling Hills Incline ChangesPerceived Exertion Level Conditioning GuidelinesExample Target Heart Rate Zone ChartStretch First P S StretchingStanding Calve Muscle Stretch Standing Quadriceps StretchImportance of Warm UP & Cool Down Tips Achieving Your Fitness GoalsWarm UP Cool DownTroubleshooting Treadmill TroubleshootingCommon Product Questions Are the Sounds MY Treadmill Makes NORMAL?Make sure the treadmill is on a level surface Troubleshooting Heart RateAfter Each USE Daily I N T E N a N C EFrame Lifetime Limited Home USE WarrantyCustomer Tech Support

700T specifications

The Triumph Plant 700T is an impressive piece of machinery that has garnered attention in the realm of construction and heavy equipment. Recognized for its robust performance, this versatile plant embodies a blend of innovative technologies and practical features that make it stand out among its competitors.

One of the key highlights of the Triumph Plant 700T is its powerful engine. Equipped with a high-efficiency diesel engine, the 700T ensures optimal performance even in the most demanding conditions. This engine not only provides excellent horsepower but also meets stringent emissions regulations, contributing to a more environmentally friendly operation. The advanced engine management system allows for fuel savings while maintaining outstanding productivity.

The 700T incorporates a cutting-edge hydraulic system, which enhances its lifting capabilities and overall performance. With a high-flow hydraulic pump, this plant is capable of handling a variety of tasks, from lifting heavy loads to precise positioning. The hydraulic system is designed for durability and efficiency, ensuring that operators can rely on consistent performance throughout the workday.

Ergonomics plays a significant role in the design of the Triumph Plant 700T. The operator cabin is spacious and thoughtfully laid out, providing a comfortable environment for long hours of operation. Equipped with user-friendly controls and intuitive dashboard displays, operators can easily monitor performance metrics and adjust settings as needed. The excellent visibility from the cabin enhances safety on the job site, allowing operators to remain aware of their surroundings.

Moreover, the Triumph Plant 700T features advanced safety systems designed to protect operators and personnel around the machine. These systems include stability monitors, emergency shutdown mechanisms, and various sensors that provide real-time feedback on the plant's operational status.

Maintenance has also been made easier with the 700T. Designed for quick access to essential components, routine checks and servicing can be performed efficiently, minimizing downtime. The robust construction of the machine ensures that it can withstand the rigors of tough working environments, making it a reliable choice for diverse projects.

In summary, the Triumph Plant 700T is a powerful, efficient, and user-friendly machine that exemplifies modern engineering. With its combination of a high-performance engine, advanced hydraulic systems, ergonomic design, and strong safety features, the 700T is an ideal solution for those seeking reliability and productivity in plant operations.
Top Page Image Contents