Cadence WCTL2982.0 user manual Touch the Right Handrail 94 to discharge any static

Page 7

6.Insert the Battery Cover (12) into the Console Base (87), with the hinges in the position shown. The Battery Cover should pivot down, away from the Console Base.

7.Hold the Console (11) near the Console Base (87).

Touch the Right Handrail (94) to discharge any static.

Locate the two wires in the Wire Harness (53) that have L-shaped connectors on the ends. Press the connectors onto the two tabs on the switch shown in inset drawing 7a.

Connect the other two wires in the Wire Harness (53) to the back of the Console Base (87) in the locations shown by the arrows in drawing 7. The connectors should slide easily into the sockets and snap into place (see drawings 7b and 7c). If the connectors do not slide easily and snap into place, turn the connectors and then insert them. IF THE CONNECTORS ARE NOT

INSERTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.

8.Set the Console (11) in the Console Base (87). Make sure that no wires are pinched. Insert as much of the Wire Harness as possible (53) down the hole in the Right Handrail (94). Securely tighten the plastic tie nearest the Right Handrail. Pull any excess Wire Harness between the plastic ties tight and tighten the other plastic tie. Cut off the ends of the plastic ties. Cover the Wire Harness with the Wire Cover (10), and route the Wire Harness out of the hole in the side of the Wire Cover. Attach the Wire Cover to the back of the Console Base with two 3/4” Screws (5). Do not over- tighten the Screws.

Make sure that no wires are pinched before you attach the Console (11) to the Console Base (87). Tighten the remaining four 3/4” Screws (5) into the Console Base and the Console. Do not overtighten the Screws.

9.Attach the Storage Latch (66) to the left Upright (14) with two 3/4” Screws (5).

10.Make sure that all parts used in assembly are prop- erly tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or carpet, place a mat under the treadmill.

6

 

 

 

 

 

 

87

 

 

 

Hinges

 

12

 

 

7

 

 

 

 

 

 

11

87

53

7a

Tabs

 

 

 

53

7b

 

 

 

 

 

Ties

 

 

 

94

7c

 

 

 

 

8

53

87

11

 

 

 

 

Ties

 

 

10

 

5

5

 

 

 

 

 

 

5

 

 

 

94

 

 

9

 

 

 

 

 

14

 

66

 

5

 

 

 

7

Image 7
Contents Model No. WCTL2982.0 Serial No QUESTIONS?Important Precautions Table of ContentsPage Right Side Before YOU BeginFront BackPliers AssemblyTreadmill until it is completely assembled Assemble the Left Upright not shown in the same way Touch the Right Handrail 94 to discharge any static HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt STEP-BY-STEP Console Operation Diagram of the ConsoleBattery Installation AA batterCALS/FAT Cals HOW to Change the Incline of the TreadmillHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use Maintenance and TroubleshootingTop View Problem The walking belt slows when walked on Workout Guidelines HOW to Measure Your Heart RateConditioning Guidelines Exercise IntensitySuggested Stretches Exercise FrequencyLimited Warranty Ordering Replacement PartsPart Identification Chart Qty Description Part LIST-Model No. WCTL2982.0R0505A