Cadence WCTL2982.0 user manual Assemble the Left Upright not shown in the same way

Page 6

3.Insert a Plastic Shim (9) into each side of the post on the right side of the Base (38). Next, hold the Right Upright (15) so the lower end is turned as shown, and insert it into the Base. Make sure that the Wire

Harness (53) does not fall into the top of the Right Upright. Be careful to avoid pinching the Wire Harness. Note: If necessary, tap the Right Upright with a rubber mallet until it is fully seated in the Base. If the Right Upright cannot be fully seated, remove the outer Plastic Shim and then insert the Right Upright.

Attach the Right Upright (15) to the Base (38) with three 1” Bolts (16) and three Star Washers (2). Do not tight- en the Bolts yet.

Assemble the Left Upright (not shown) in the same way.

4.If there are plastic ties in the brackets on the Handrails, remove them. Hold one of the Handrails near the Right Upright (15) as shown. Insert the Wire Harness (53) up through the bracket on the Handrail and out of the round hole in the side of the Handrail. If necessary, use needlenose pliers to pull the Wire Harness out of the hole. Be careful not to damage the Wire Harness. Insert the bracket into the top of the Right Uprights (15).

Attach the other Handrail as described above. Note: There are no wires in the Left Upright (14).

Hand tighten four 1” Bolts (16) with Handrail Washers

(7)into the Uprights (14, 15) and the Handrails.

5.Set the Console Base (87) on the Handrails (94, 4). Thread four 1 1/4” Tek Screws (86) into the Handrails and the Console Base. After you have started all four Screws, tighten the Screws until they are snug; do not overtighten the Screws.

Firmly tighten, but do not overtighten, the bolts used in steps 2 through 4.

Insert the Wire Harness (53) through the two indicated plastic ties on the Console Base (87) and up through the hole in the Console Base.

3

 

 

 

 

 

 

 

 

53

 

 

 

 

 

15

 

 

 

 

 

 

Orient the

 

 

 

 

Upright as

 

 

 

 

shown.

 

 

 

 

9

2

 

 

 

 

16

 

 

 

 

2

 

 

 

 

 

16

38

 

 

 

 

 

 

4

 

 

Left Handrail

 

 

 

 

 

Right Handrail

 

 

 

16

53

 

 

 

 

 

 

 

 

 

7

 

 

 

 

 

Connectors

 

 

 

 

7

Bracket

 

 

 

 

 

 

16

 

 

14

 

16

 

 

 

 

7

 

 

 

 

 

16

 

 

 

 

 

15

5

 

53

 

Connectors

4

 

94

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

87

 

 

 

 

Plastic Ties

 

 

 

 

86

86

 

 

 

 

 

 

6

Image 6
Contents QUESTIONS? Model No. WCTL2982.0 Serial NoTable of Contents Important PrecautionsPage Back Before YOU BeginFront Right SideAssembly PliersTreadmill until it is completely assembled Assemble the Left Upright not shown in the same way Touch the Right Handrail 94 to discharge any static Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt AA batter Diagram of the ConsoleBattery Installation STEP-BY-STEP Console OperationHOW to Change the Incline of the Treadmill CALS/FAT CalsHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USEMaintenance and Troubleshooting Problem The power turns off during useTop View Problem The walking belt slows when walked on Exercise Intensity HOW to Measure Your Heart RateConditioning Guidelines Workout GuidelinesExercise Frequency Suggested StretchesOrdering Replacement Parts Limited WarrantyPart Identification Chart Part LIST-Model No. WCTL2982.0 Qty DescriptionR0505A