Epic Fitness ECTL81804.1 manual Treadmill Operation, PRE-LUBRICATED Walking Belt

Page 9

TREADMILL OPERATION

THE PRE-LUBRICATED WALKING BELT

Your treadmill features a walking belt coated with high- performance lubricant. IMPORTANT: Never apply sil- icone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

DANGER: Improper connection of the equipment-grounding conductor can result in an increased risk of electric shock.

and plug the surge suppressor into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Important: The treadmill is not compatible with GFCI-equipped outlets.

This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illus- trated in drawing 1 below. A temporary adapter that looks like the adapter illustrated in drawing 2 may be used to connect the surge suppressor to a 2-pole receptacle as shown in drawing 2 if a properly grounded outlet is not available.

1

Check with a qualified electrician or service- man if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product—if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Your treadmill, like any other type of sophisticated electronic equipment, can be seriously damaged by sudden voltage changes in your home’s power. Voltage surges, spikes, and noise interference can result from weather conditions or from other appliances being turned on or off. To decrease the possibility of your treadmill being damaged, always use a surge suppressor with your treadmill (see drawing 1 at the right).

2

Grounded Outlet Box Surge Suppressor

Grounding Pin

Grounding Pin

Grounded Outlet

Grounding Plug

 

Grounded Outlet Box

Adapter

Surge Suppressor

Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge sup- pressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps. There must be a moni- toring light on the surge suppressor to indicate whether it is functioning properly. Failure to use a properly functioning surge suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change speed, accelerate, or stop unexpect- edly, which may result in a fall and serious injury.

This product must be grounded. If it should malfunc- tion or break down, grounding provides a path of least resistance for electric current to reduce the risk of elec- tric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. Plug the power cord into a surge suppressor,

Lug

Metal Screw

The temporary adapter should be used only until a properly grounded outlet (drawing 1) can be installed by a qualified electrician.

The green-colored rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used it must be held in place by a metal screw. Some 2-pole receptacle outlet box covers are not grounded. Contact a qualified elec- trician to determine if the outlet box cover is grounded before using an adapter.

9

Image 9
Contents Model No. ECTL81804.1 Serial No QUESTIONS?Table of Contents Important Precautions Page For your benefit, read this manual carefully before Before YOU BeginRight Side BackDo not tighten the Upright Bolt yet AssemblyBolts Be careful to avoid pinching the Upright Wire HarnessSmall Screws Cylinder Wire 117 HOW to Plug in the Power Cord Treadmill OperationPRE-LUBRICATED Walking Belt Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerFollow your progress with the matrix Displays Matrix-When Change the incline of the treadmill as desiredDistance display- If no goals were set, this Pulse/PaceStand on Foot rails Measure your heart rate if desiredHOW to USE a Preset Program Follow your progress with the displays Select one of the custom programs HOW to Create a Custom ProgramHOW to USE a Custom Program Enter your age and a maximum speed setting HOW to USE a Heart Rate ProgramPut on the optional chest pulse sensor Select a heart rate programFollow your progress with the displays HOW to Connect Your Portable CD Player HOW to Connect Your Computer HOW to Connect Your Home StereoHOW to Connect Your VCR Audio Adapter CablePressVCR. the Play button on your CD player or Measure your heart rate if desired Follow the on-line instructions to start Program HOW to USE a Program Directly from OUR WEB SiteReturn to the treadmill and stand on the foot Follow your progress with the matrix DisplaysInformation MODE/DEMO Mode HOW to Adjust the Cushioning SystemOptional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingSwitch. Make sure that the gap between the Magnet Reed Switch is about 1/8. If necessary, loosen TopProblem The walking belt slows when walked on Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyKey Qty Description R0705AExploded DRAWING-Model No. ECTL81804.1 124 117 108 112 110 114 111 116 101 104 Limited Warranty HOW to Order Replacement Parts