Epic Fitness ECTL81804.1 manual Assembly, Do not tighten the Upright Bolt yet

Page 6

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor- mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included allen wrench and your own phillips screwdriver .

For help identifying assembly hardware, see the drawings below. Note: If a part is not found in the part bags, check to see if the part has been preattached.

Upright Bolt (86)–16

Latch Bolt (77)–2

 

 

3/8” Star

 

 

 

Washer (88)–8

 

IMPORTANT: Do not extend the Frame (16) past the ver-

1

90

 

tical position before the console base is assembled or

 

 

 

you may damage the gas spring.

 

86

95

1. Slide the Right and Left Uprights (90, 95) onto the

 

 

 

brackets on the Base (99). Make sure that the

 

 

 

Uprights are on the correct sides; the indicated

 

 

86

holes must be facing away from the treadmill.

 

 

 

 

 

Raise the Right Upright (95) until the lower hole in the

 

 

 

front of the Right Upright is aligned with the upper hole

 

 

 

in the right bracket on the Base (99). Finger tighten an

 

 

 

Upright Bolt (86) into the Right Upright and the bracket.

 

 

 

Do not tighten the Upright Bolt yet.

 

 

 

Repeat this step with the Left Upright (90).

 

 

Holes

 

 

99

 

 

 

 

 

16

 

6

Image 6
Contents QUESTIONS? Model No. ECTL81804.1 Serial NoTable of Contents Important Precautions Page Right Side Before YOU BeginFor your benefit, read this manual carefully before BackAssembly Do not tighten the Upright Bolt yetBe careful to avoid pinching the Upright Wire Harness BoltsSmall Screws Cylinder Wire 117 HOW to Plug in the Power Cord Treadmill OperationPRE-LUBRICATED Walking Belt Features of the Console HOW to Turn on the Power HOW to USE the Manual ModeDistance display- If no goals were set, this Change the incline of the treadmill as desiredFollow your progress with the matrix Displays Matrix-When Pulse/PaceMeasure your heart rate if desired Stand on Foot railsHOW to USE a Preset Program Follow your progress with the displays HOW to Create a Custom Program Select one of the custom programsHOW to USE a Custom Program Put on the optional chest pulse sensor HOW to USE a Heart Rate ProgramEnter your age and a maximum speed setting Select a heart rate programFollow your progress with the displays HOW to Connect Your Portable CD Player HOW to Connect Your Home Stereo HOW to Connect Your ComputerHOW to Connect Your VCR Audio Adapter CablePressVCR. the Play button on your CD player or Measure your heart rate if desired Return to the treadmill and stand on the foot HOW to USE a Program Directly from OUR WEB SiteFollow the on-line instructions to start Program Follow your progress with the matrix DisplaysInformation MODE/DEMO Mode HOW to Adjust the Cushioning SystemOptional Chest Pulse Sensor HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Switch. Make sure that the gap between the Magnet TroubleshootingProblem The power turns off during use Reed Switch is about 1/8. If necessary, loosen TopProblem The walking belt slows when walked on Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyR0705A Key Qty DescriptionExploded DRAWING-Model No. ECTL81804.1 124 117 108 112 110 114 111 116 101 104 HOW to Order Replacement Parts Limited Warranty