Gold's Gym CWTL05607.0 manual Not Connected PROPERLY, the CON, Sole MAY be Damaged When

Page 8

5. Attach two Base Pads (82) to the Base (108)

5

 

 

with two #8 x 1" Tek Screws (83) as shown.

 

 

 

 

 

Insert the other Extension Leg (89) into the

82

108

 

Base (108) as shown. Hold two Extension Leg

 

 

 

 

Nuts (67) in the bottom of the Extension Leg.

 

 

65

Next, insert two 5/16" x 2 1/4" Bolts (65) into the

 

 

 

 

82

top of the Extension Leg, and firmly tighten the

 

 

 

 

 

Bolts into the Extension Leg Nuts. .

 

 

 

 

83

 

 

 

 

67

 

 

 

 

89

6. With the help of a second person, carefully raise

6

 

 

the Right Upright (107) and the Left Upright (not

 

 

 

 

 

shown) to a vertical position.

 

 

 

Have the second person hold the console as-

 

Console

 

 

Assembly

 

sembly near the Right Upright (107) as shown.

 

 

 

Look under the console assembly and locate

 

 

 

the Console Wire (66).

 

 

 

Connect the Upright Wire (77) to the Console

 

 

66

Wire (66). See the inset drawing. The connec-

 

Wire

 

77

tors should slide together easily and snap

 

 

Tie

into place. If they do not, turn one connector

66

 

 

 

and try again. IF THE CONNECTORS ARE

 

 

 

NOT CONNECTED PROPERLY, THE CON-

77

 

107

SOLE MAY BE DAMAGED WHEN THE

 

 

 

 

POWER IS TURNED ON. Remove the wire tie

 

 

 

from the Upright Wire.

 

 

 

7. Insert the Upright Wire (77) and the Console

7

 

 

Wire (66) into the Right Upright (107).

 

 

Console

 

 

 

Set the console assembly on the Uprights (84,

Assembly

 

 

 

 

107). Be careful not to pinch the wires. While

 

 

 

a second person holds the console assembly,

 

 

 

attach it with four 5/16" x 1" Bolts (64) and four

 

 

 

5/16" Star Washers (8); start all four Bolts and

 

 

 

then firmly tighten them.

 

 

 

 

 

77, 66

 

Plug in the power cord as described on page

 

 

 

11, and turn on the power as described on page

 

8

 

13. (Note: The treadmill may automatically rise

 

64

8

to the maximum incline level and then return to

 

 

 

the minimum level.) Adjust the incline to the low-

 

107

64

est incline level as described in step 4 on page

 

84

14.

 

 

 

 

 

 

8

 

 

Image 8 Contents
Call TOLL-FREE QUESTIONS?Model No. CWTL05607.0 Serial No Table of Contents Important Precautions Page Before YOU Begin Assembly Be careful not to pinch the Upright Wire Tighten the Bolts yetNot Connected PROPERLY, the CON Sole MAY be Damaged WhenTo overtighten the Bolts Top ViewPage PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeSelect the manual mode Insert the key into the consoleChange the incline of the treadmill as desired Follow your progress with the displayMeasure your heart rate if desired Turn on the fan if desiredPress the Start button to start the workout HOW to USE a Cross Trainer WorkoutSelect one of the six cross trainer workouts Perform the first strength exercise when prompted Continue the cross trainer workoutHOW to USE a Distance Workout Select a distance workoutHOW to USE a Preset Workout Information Mode HOW to Adjust the Cushioning System Optional Chest Pulse SensorHOW to USE the Upper Body Arms HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useProblem The walking belt slows when walked on TopPage Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches R0208A Qty DescriptionDescription Exploded Drawing A-Model No. CWTL05607.0 R0208A Exploded Drawing B-Model No. CWTL05607.0 R0208A Exploded Drawing C-Model No. CWTL05607.0 R0208A Exploded Drawing D-Model No. CWTL05607.0 R0208A Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty