Healthrider HRTL89406.0 manual Assembly, Make sure that the power cord is unplugged

Page 7

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed.

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex key and your own phillips screwdriver , and rub-

ber mallet . For help identifying the assembly hardware, see the drawings below. The number in parentheses below each drawing is the key number of the part, from the PART LIST on pages 30 and 31. The number following the parentheses is the quantity needed for assembly. Note: Some small parts may have been preassembled. If a part is not in the parts bag, check to see if it has been preassembled. To avoid damag- ing plastic parts, do not use power tools for assembly.

Nut (20)–2

3/8” Star

1” Tek Screw (82)–4

Washer (71)–4

Lower Latch Shock Bolt (3)–1

 

 

Upper Latch Shock Bolt (4)–1

 

Extension Leg Bolt (87)–4

Console Bolt (72)–4

1. Make sure that the power cord is unplugged.

1

 

 

 

 

 

 

 

With the help of a second person, carefully tip

 

 

 

 

the treadmill onto its left side as shown. Partially

 

 

85

 

fold the Frame (55) so that the treadmill is more

 

 

 

81

stable. Do not fully fold the Frame until the

 

 

 

 

 

 

 

treadmill is completely assembled.

 

 

 

 

Insert an Extension Leg (97) into the base of the

55

 

81

82

 

 

Uprights (85) as shown. Tighten two Extension Leg

 

 

 

 

Bolts (87) into the bottom of the Extension Leg.

 

 

 

 

Attach two Base Pads (81) to the base of the

 

97

87

 

Uprights (85) with two 1” Tek Screws (82).

 

 

 

 

With the help of a second person, tip the tread-

 

 

 

 

mill over onto it’s right side. Attach the other

 

 

 

 

Extension Leg and Base Pads (not shown) as

 

 

 

 

described above.

 

 

 

 

With the help of a second person, carefully raise

 

 

 

 

the treadmill so that all four Base Pads (81) are on

 

 

 

 

the floor and the Frame (55) is in a vertical position

 

 

 

 

(see drawing 3).

 

 

 

 

 

7

 

 

 

Image 7
Contents Model No. HRTL89406.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Power Lines Before YOU Begin Make sure that the power cord is unplugged AssemblyTop Page HOW to Connect a 75 OHM Catv Cable HOW to Connect AN AntennaHOW to Connect a VCR Chest Pulse Sensor Troubleshooting HOW to USE the Chest Pulse SensorHOW to PUT on the Chest Pulse Sensor Chest Pulse Sensor Care and MaintenanceHOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerContacts for about 15 seconds Follow your progress with the displaysMeasure your heart rate if desired Pulse sensor. Next, stand on the foot railsWhenkey. you are finished exercising, remove HOW to USE a Preset ProgramSelect a preset program Turn on the fan if desiredWorkout Intensity bar Incline settings for the next segmentSelect a Distance program HOW to USE a Distance ProgramTurn on the fans if desired Programsettings. the desired speed and incline HOW to Create a Custom ProgramSelect a Custom program HOW to USE a Custom Program Adjust the maximum target heart rate setting if Desired HOW to USE a Pulse ProgramSelect a Pulse program Follow your progress with the displays Workout Intensity bar Press the Channel buttons to select Desired channel HOW to Operate the Personal TelevisionPress the Volume buttons to adjust the volume Press the On/Off button to turn on TelevisionPress the On/Off button again and add or Delete channels HOW to USE the Information ModeHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TroubleshootingTop View Problem The walking belt slows when walked on Problem The chest pulse sensor does not function properly Problem Television reception is poorExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesQty Description R1106AOrdering Replacement Parts Exploded Exploded Drawing B-Model No. HRTL89406.0 R1106A Exploded Drawing C-Model No. HRTL89406.0 R1106A Exploded Drawing D-Model No. HRTL89406.0 R1106A Limited Warranty