Healthrider HRTL20001 manual Snaps into the storage latch. Make sure that the locking, 105

Page 6

5.Move your right hand to the position shown at the right, and hold the treadmill firmly. Using your left hand, lift the storage latch. Raise the treadmill until the locking pin

snaps into the storage latch. Make sure that the locking

pin is inside the storage latch, and that the storage latch is fully closed.

6.See drawing 6B. Attach a Base Pad (73) to the bottom of the Stabilizer Plate (88) in the indicated location.

See drawing 6A. Stand behind the treadmill. Hold the Left Crossbar Bracket (4) and the Right Crossbar Bracket (not shown). Place one foot on the Base (75) in the indicated location.Tip the treadmill back slightly. While the treadmill is held in this position, a second person should slide the Stabilizer Plate (88) onto the Base (see drawing 6C). Keeping your foot on the Base, carefully tip the treadmill up until it is resting on the Base. Make sure that the Stabilizer Plate (88) stays on the Base.

See drawing 6C. Attach the Stabilizer Plate (88) to the Base (75) with a Stabilizer Plate Bolt (105), two Washers

(97), and the Stabilizer Plate

Nut (95) as shown.

Before moving the treadmill, see HOW TO MOVE THE

TREADMILL on page 11.

7.Refer to assembly drawing 5 at the top of this page. Hold the upper end of the treadmill with your right hand as shown. Using your left hand, lift the storage latch. Pivot the treadmill slightly until the locking pin is out of the stor- age latch.

Hold the treadmill firmly with both hands, and lower the treadmill to the floor. To decrease the possibility of in- jury, bend your legs and keep your back straight.

8.Remove the paper backing from the Adhesive Clip (44). Press the Adhesive Clip onto the Frame (84) in the indi- cated location. Press the Allen Wrench (57) into the Adhesive Clip. The use of the Allen Wrench is described on page 13.

Make sure that all parts are tightened before you use the treadmill. Note: Place a mat beneath the treadmill to pro- tect the floor or carpet.

5

 

 

 

Storage Latch

 

 

 

 

 

 

Locking Pin

6A

 

 

6B

 

4

 

88

 

 

 

 

 

 

73

 

 

 

88

 

 

 

75

6C

95

97

 

 

 

 

 

 

 

 

 

105

 

 

75

88

7

 

 

 

8

 

 

 

44

 

 

 

57

84

 

 

6

Image 6
Contents QUESTIONS? Customer HOT LineTable of Contents Important Precautions Back Before YOU BeginFor your benefit, read this manual carefully before FrontWrench AssemblyAssembly requires two people Legs rather than your backSnaps into the storage latch. Make sure that the locking 97, and the Stabilizer Plate105 Operation and Adjustment Adjust the speed in small increments SettingSTEP-BY-STEP Console Operation Desired mode Press the START/STOP buttonFollow your progress with the monitor displays Pulse will not be detected Information ModeNot press Too hard, or Circula SteadilyHOW to Fold the Treadmill for Storage HOW to Move the TreadmillHOW to Lower the Treadmill for USE Symptom the Power Turns OFF During USE TROUBLE-SHOOTINGSymptom the Power does not Turn on TrippedSymptom the Walking Belt Slows When Walked on Symptom the Walking Belt is OFF-CENTER When Walked onSymptom the Treadmill Sits Unevenly on the Floor AGE Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Healthrider Acquisition Corp., Inc., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty Part No F02855-C R0896ARemove this Exploded Drawing and Part List from the Manual Choke DescriptionController Right Crossbar BracketExploded DRAWING-Model No. HRTL20001