JVC UX-H35 manual Turning On the Power, Adjusting the Volume, Adjusting the Tone Bass/Treble

Page 14
AHB PRO

Turning On the Power

 

To turn on the unit, press

STANDBY/ON

STANDBY/ON

( on the unit).

 

The STANDBY lamp on the unit goes off.

 

•When you press the source button

—3/8CD, 2 3 TAPE, TUNER (or

BAND TUNER on the unit) and AUX, the unit automatically turns on and starts playback if the source is ready.

To turn off the unit (standby), press

STANDBY/ON ( on the unit) again. The STANDBY lamp on the unit lights on.

•The CLOCK indicator and “0:00” flash on the display until you set the built-in clock. After setting the clock, the clock time will appear on the display while the unit is on standby.

•A little power is always consumed even while the unit is on standby.

To switch off the power supply completely, unplug

the power cord.

When you unplug the power cord or if a power failure occurs

The clock is reset to “0:00” right away, while the tuner preset stations (see page 12) will be erased in a few days.

Adjusting the Volume

You can adjust the volume level only while the unit is turned on. The volume level can be adjusted between “VOL MIN” and “VOLUME 1” – “VOLUME 40 (VOL MAX).”

Press VOLUME + to increase the volume or press VOLUME – to decrease it.

VOLUME

For private listening

Connect headphones to the PHONES jack. No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on headphones.

DO NOT turn the unit off (standby) with the volume set to an extremely high level; otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the unit or start playing any source next time. REMEMBER you cannot adjust the volume level while the unit is on standby.

Adjusting the Tone (Bass/Treble)

You can adjust the bass level (low frequency range) and the treble level (high frequency range) within a range of –5 to +5.

When shipped, the bass level set to “BASS 0” and the treble level set to “TREBLE +1.”

•This function only affects the playback sound, and does not affect your recording.

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start over from step 1.

On the remote control ONLY:

1Press BASS to adjust the bass level or press TREBLE to adjust the treble

level.

BASSTREBLE

2 Press UP to increase the

UP

 

 

level or press

DOWN to

 

decrease it.

 

DOWN

Reinforcing the Bass Sound

You can reinforce the bass sound to maintain rich, full bass at low volume—Active Hyper Bass Pro.

•This function only affects the playback sound, and does not affect your recording.

To get the effect, press AHB PRO so that the BASS indicator lights up on the display.

•Each time you press the button, the

bass reinforcement alternates between on (AHB ON) and off (AHB OFF).

To cancel the effect, press AHB PRO again so that the BASS indicator goes off.

11

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Micro Component System Page Important for Laser Products About This Manual PrecautionsIntroduction Contents Top view Location of the ButtonsMain Unit Front viewDisplay window Main unit Display windowRemote Control Pressing one of these buttons also turns on the unitGetting Started Supplied AccessoriesConnecting Antennas FM antennaRelease your finger from the clamp Connecting SpeakersTurn the AM loop antenna until you have the best reception To connect an outdoor AM antennaTo remove the speaker grilles Connecting Other EquipmentTo connect the AC power cord To connect an audio equipmentPutting the Batteries into the Remote Control When using the unit in your carSetting the Clock Common OperationsAdjusting the Tone Bass/Treble Turning On the PowerAdjusting the Volume Reinforcing the Bass SoundListening to FM and AM Broadcasts Tuning in to a StationPresetting Stations Press SET Tuning in to a Preset StationTune in to the station you want to preset Press SET againPress 0 Open on the unit When playing a CD-R or CD-RWPlaying Back Discs General notesBasic Disc Operations Programming the Playing Order of the Tracks-Program PlayRepeating Tracks-Repeat Play To check the program contentsPlaying at Random-Random Play Press RandomPress for cassette deck on the unit Playing Back TapesPlaying Back a Tape Put a cassette in with the exposed part of the tape downRecording on a Tape To record on both sides-Reverse ModeRecording To protect your recordingPress ONE Touch Disc Direct RecordingOne Track Recording Repeat steps 2 and 3 to record other tracks you wantSet the on-time when you want the unit To turn on Using the TimersUsing Daily Timer and Recording Timer Set the off-time when you want the unit To turn off standbyTo deactivate the timer temporarily Adjust the clock if you needSelect the volume level With the source to playHow the Sleep Timer actually works Using Snooze TimerUsing Sleep Timer Press SleepHandling cassette tapes MaintenanceCleaning the unit Handling discsTroubleshooting Specifications0403MWMMDWJEM
Top Page Image Contents