NordicTrack NTXC80182 user manual HOW to Adjust the SKI Exerciser

Page 6

HOW TO ADJUST THE SKI EXERCISER

HOW TO ADJUST THE RESISTANCE OF THE SKIS

To vary the intensity of your exercise, you can change your exercise pace, use the arm cord (see the section below), or adjust the resistance of the skis. CAUTION:

Always dismount the ski exerciser before adjust- ing the resistance of the skis.

For greater

 

 

adjustments

 

 

in the length

 

 

of the Arm

 

 

Cord (23),

 

 

add one loop

23

23

of the Arm

 

 

 

Cord around

 

 

To increase the resistance of the skis, slide the Resistance Clamp (85) to a higher position on the Upright (16). To decrease the resistance, slide the Resistance Clamp to a lower position.

85

16

the pulley as

shown, or remove one loop from the pulley.

HOW TO ADJUST THE POSITION OF THE HIP PAD

Loosen the Adjustment

53

Knob (41) on each side of

 

the Hip Pad Slide (42), and

 

slide the Hip Pad Slide to

 

the desired position. The

 

Hip Pad (53) should be at

 

HOW TO ADJUST THE RESISTANCE OF THE ARM CORD

The resistance of the Arm

39 88

Cord (23) can be adjusted

with the Resistance Knob

 

(39) above the Pulley (35).

 

Turn the Knob clockwise to

 

increase the resistance, or

35

counterclockwise to

 

decrease the resistance.

23

Note: As you turn the

 

Resistance Knob, the num-

 

bered Resistance Scale

 

Decal (88) will protrude through the Knob to show the

resistance setting.

 

WARNING: The Pulley (35) will get hot during use. Avoid touching the Pulley immediately after use.

HOW TO ADJUST THE LENGTH OF THE ARM CORD

When the Arm

 

 

 

Cord (23) is

 

 

 

adjusted to the

 

 

 

proper length,

23

 

 

your arms

24

Knot

 

should extend

 

 

 

just behind your

 

 

 

hips when you

 

 

 

use the Arm Cord. To adjust the length of the Arm Cord, retie the knot inside each Handgrip (24).

hip level, about one inch

 

42

below your navel. The Hip

41

 

Pad should be high

 

 

enough that it does not

 

 

restrict leg movement, and

 

 

low enough that it does not press against your

abdomen. Firmly retighten both Adjustment Knobs.

HOW TO ADJUST THE ELEVATION OF THE SKI EXERCISER

Increasing the elevation of the ski exerciser will simu- late uphill skiing. This will further develop the quadri- ceps muscles on the fronts of your thighs, elevate your heart rate more quickly, and provide a more intense workout.

To adjust the elevation,

 

first loosen the Incline

76

Knob (93) in front of one

93

of the Legs (76). Insert the

straight end of a Leg Pin

 

(74) into the hole in the

2

Leg Bracket (2) and one of

74

the holes in the Leg. Make

 

sure that the Leg Pin

 

goes completely through

 

the holes and that the

bent end of the Leg Pin points toward the floor. Rotate the Leg Pin to secure it around the Leg. Retighten the Incline Knob.

Repeat this process with the other Leg (not shown).

Make sure that both Legs are at the same height.

6

Image 6 Contents
Model No. NTXC80182 Serial No Customer HOT LineTable of Contents Important PrecautionsBefore YOU Begin Assembly Raise the Upper Body Arm 27 to position as shown HOW to Adjust the SKI Exerciser ADD ARM Swings to the LEG Motion HOW to USE the SKI ExerciserStart with LEG Motion only Combine the ARM and LEG MotionsBattery Installation HOW to Operate the ConsoleDescription of the Console Lubricating the Resistance PAD Maintenance and StorageCleaning the SKI Exerciser Caring for the Resistance Strap and FlywheelGeneral Lubrication StorageTroubleshooting Problem The arm cords are tangledProblem The skis slip Problem The rollers squeak or stickWorkout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencyPart LIST-MODEL NO. NTXC80182 Qty DescriptionExploded DRAWING-MODEL no HOW to Order Replacement Parts Limited Warranty
Related manuals
Manual 16 pages 19.24 Kb