NordicTrack NTC59020 HOW to USE the Manual Mode, Begin pedaling to activate the console, Display

Page 10

HOW TO USE THE MANUAL MODE

1 Begin pedaling to activate the console.

The exercise cycle requires no batteries or external power source. Power is supplied by

a generator as you pedal.To activate the con-

sole, begin pedaling at a speed of about 3 miles per hour or faster. After a few seconds, the con- sole displays will light. A tone will then sound and the console will be ready for use.

2 Select the manual mode.

When the power is turned on, the

manual mode will be selected. If you have selected a

program or the iFIT.com mode,

select the manual mode by pressing the Program Select button repeatedly until a track appears in the matrix.

Begin pedaling and change the resistance of

3the exercise cycle as desired.

As you pedal,

change the resis- tance of the exer- cise cycle by pressing the Resistance but-

tons. There are

ten resistance levels. Note: After the Resistance buttons are pressed, it will take a moment for the exercise cycle to reach the selected resistance level.

Monitor your progress with the matrix, the

4 Training Zone bar, and the two displays.

The matrix — When the manual

mode or the iFIT.com mode is selected, the

matrix will show a track representing

1/4 mile. As you exercise, the indicators around

the tr ack will flash to indicate your position on the

track. When you have completed a lap, a new lap will begin.

The Training Zone bar —The Training Zone bar will show your pace and the approximate inten-

sity level of your exercise. For exam-

ple, if three or four indicators in the bar are lit, the bar shows that your pace is ideal for fat burning. During programs, the Training Zone bar will also prompt you to increase or decrease your pace.

The left display

The left display will

 

show the elapsed

 

time, your pedaling

 

pace (measured in

 

minutes per mile

),

and the distance

 

you have pedaled. The display will change from one number to the next every few seconds, as shown by the indicators around the display. Note: When a program is selected, the display will show the time remaining in the program and the time remaining in the current segment of the program instead of the elapsed time.

If you stop pedaling for several seconds, a tone

will sound, the console will pause, and the left dis- play will begin to flash.

The right

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

display

—The right

 

 

 

 

 

 

 

 

 

 

 

 

 

display will show

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

your pedaling

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

speed, the approxi-

 

 

 

 

 

 

 

 

 

 

 

 

 

mate numbers of

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

fat calories

and

 

 

 

calories

you have burned (see FAT BURNING on

 

 

 

page 21), and the resistance level of the exercise cycle. The display will change from one number to the next every few seconds, as shown by the indi- cators. The display will also show your heart rate when you use the handgrip pulse sensor or the optional chest pulse sensor. Note: Each time the resistance of the exercise cycle changes, the dis- play will show the resistance level.

10

Image 10
Contents QUESTIONS? Customer HOT LineTable of Contents Important PrecautionsYou use the exercise cycle Before YOU BeginRight Side Assembly Assembly requires two personsSlide Upper Wire HarnessCarefully pull Upright onto the FrameGround Wires Pulse On the Console. Next, locate the two pulse wiresDo not pinch Wires during This step Have another person hold the Console 4 near the HandlebarInstalling the Receiver for the Optional Chest Pulse Sensor HOW to Adjust the Seat HOW to Move and Level the Exercise CycleHOW to Adjust the Seat Post Left Display Matrix Console DiagramFeatures of the Console Cassettes areBegin pedaling to activate the console HOW to USE the Manual ModeSelect the manual mode Generator as you pedal.To activate the conPlastic on Measure your heart rate if desiredThin sheets PlasticRight HOW to USE Resistance and Pace ProgramsSelect one of the six resistance and pace Programs LeftSelect one of the heart rate programs HOW to USE Heart Rate ProgramsMonitor your progress with the two displays 3Enter your agePedaling to start the program Hold the handgrip pulse sensorColumn to the left HOW to Connect Your CD PLAYER, VCR Or Computer HOW to Connect Your Portable StereoAudio Cable Adapter Phones jack, see instruction BLine OUT jack Adapter Audio Cable HOW to Connect Your VCRAdapter Free Pace setting is about to changeTo pur Video programReturn to the exercise cycle and begin Pedaling HOW to USE Programs Directly from OUR WEB SiteFollow the on-line instructions to start Program Chest pulse sensor, call toll-freeHOW to Adjust the Drive Belt HOW to Adjust the Reed SwitchPulse Sensor Troubleshooting Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. NTC59020 Qty Description Key No. QtyR1102A 3968Limited Warranty HOW to Order Replacement PartsPart No R1102A
Related manuals
Manual 24 pages 11.24 Kb