NordicTrack NTCCXC80180 user manual HOW to a Djust

Page 6

HOW TO A DJUST THE

S KI E XERCISER

HOW TO ADJUST THE RESISTANCE OF THE SKIS

To vary the intensity of your exercise, the amount of leg resistance can easily be adjusted by moving the resistance clamp on the upright. CAUTION: Always

dismount the ski exerciser before adjusting the resistance of the skis.

To increase the resistance

 

of the skis, raise the

85

Resistance Clamp (85).

 

Decrease the resistance by

 

lowering the Resistance

 

Clamp.

 

The intensity of your exer- cise can also be varied by using the arm cords (see the section below), or by changing the pace of your exercise.

HOW TO ADJUST THE ARM CORD RESISTANCE

The resistance of the Arm

39

88

Cord (23) can be adjusted

 

 

by turning the Resistance

 

 

Knob (39) on top of the

 

 

Pulley (35). Turn the Knob

 

 

clockwise to increase the

35

 

resistance. Turn the Knob

 

 

 

counterclockwise to

23

 

decrease the resistance.

 

 

 

Note: As you turn the

 

 

Resistance Knob to

 

 

increase the resistance, the numbered Resistance

 

Scale Decal (88) will protrude through the Knob to show the resistance settings.

CAUTION: The Pulley (35) will get hot during use. Avoid direct contact with the Pulley immediately after use.

ADJUST THE ARM CORD LENGTH

The proper

 

 

 

Arm Cord

 

 

 

(23) length

 

 

 

should allow

23

24

Knot

your arms to

 

 

 

 

extend just

 

 

 

beyond your

 

 

 

hips. The arm cord length can be adjusted by retying the knots inside the Handgrips (24).

For greater adjustments in the cord length, one loop of the cord can be added to or removed from the pul-

ley as shown at the right.

HOW TO ADJUST THE POSITION OF THE HIP PAD

Loosen the Adjustment

53

Knobs (41) on each side of

 

the Hip Pad Slide (42).

 

Move the Hip Pad Slide to

 

the desired position. The

 

Hip Pad (53) should rest at

 

hip level, about one inch

42

below your navel. The Hip

41

Pad should be high enough

 

so it does not restrict leg

 

movement and low enough

 

so it does not press against your abdomen.

Tighten the Adjustment Knobs (41) to hold the Hip Pad (53) in position. Make sure both Knobs are secure.

HOW TO ADJUST THE ELEVATION OF THE SKI

EXERCISER

Increasing the elevation and the leg resistance will simulate skiing uphill. This will further develop the quadriceps muscle group in the front of your thighs, elevate your heart rate more quickly and provide you with an even more intense workout.

You may select an elevation up to level ten. There is an increase of two degrees per hole.

To adjust the elevation,

 

insert the straight end of a

 

Leg Pin (74) completely

2

through the holes in the Leg

 

(76) and Leg Bracket (2).

 

The bent end of the Leg Pin

74

should point toward the

76

floor as shown.Make sure

that the Leg Pin goes

 

completely through the

 

holes. Rotate the bent end

 

of the Leg Pin to secure it in place. Repeat this process on the other Leg (not shown).

6

Image 6
Contents Customer Service Department Model No. NTCCXC80180Able Contents Before YOU Begin Ssembly Locked into position on both sides of the Hip Pad Slide HOW to a Djust Battery Installation HOW to Operate the ConsoleDescription of the Console You slide away from the hip pad HOW to U SE the S KI E XerciserStart with the LEG Motion only Is pushing back. Do not bring either foot in front4Lubrication of the Resistance PAD Cleaning the SKI ExerciserAintenance Care for the Resistance Strap FlywheelGeneral Lubrication Should not Be oiled. FollowStorage Problem The console does not function properly Problem The arm cords are tangledROUBLE-SHOOTING Problem The skis are slipping Problem The rollers are squeaking or stickingSolution Workout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Page Model DescriptionRawing -M Customer Record HOW to O Rder R Eplacement Imited Warranty Icon of CANADA, 900 de l’Industrie, St. Jérôme, QC J7Y 4B8