NordicTrack NTL07707.1 user manual Make sure that the power cord is unplugged

Page 7

1.Make sure that the power cord is unplugged.

With the help of a second person, carefully tip the treadmill onto its left side. Partially fold the Frame (56) so that the treadmill is more stable; do not fully fold the Frame yet.

Remove and discard the two indicated bolts (A) and the shipping bracket (B).

Cut the ties securing the Upright Wire (38) to the Base (83). Locate the tie in the indicated hole in the Base, and use the tie to pull the Upright Wire out of the hole.

Attach a Base Pad (81) to the Base (83) in the location shown with a Base Pad Spacer (13) and a #8 x 1" Tek Screw (2). Then, attach another Base Pad (81) with only a #8 x 1" Tek Screw (2).

2.Remove the 3/8" Nut (8), the 3/8" x 2" Bolt (4), and the shipping bracket (C) from the Base (83). Attach a Wheel (84) with the Bolt and the Nut that you just removed. Do not overtighten the Nut; the Wheel must turn freely. Discard the shipping bracket.

3. Identify the Right Upright (78) and the Right

Upright Spacer (79), which are marked with

stickers. Insert the Upright Wire (38) through the

Right Upright Spacer as shown.

1

 

 

 

 

B

A

83

 

 

Hole

 

 

 

38

 

 

81

Tie

 

 

2

13

81

 

 

56

2

 

 

 

 

 

2

 

 

 

 

83

 

 

4

 

 

 

 

84

 

 

C

 

 

 

8

 

 

 

3

 

 

 

38

78

 

 

 

 

 

See the inset drawing. Tie the long tie in the

Right Upright (78) securely around the end of

the Upright Wire (38). With the help of a second

person, hold the Right Upright near the Base

(83). Then, pull the other end of the long tie until

the Upright Wire is routed completely through

the Right Upright.

Long Tie

38

79

 

78

38

Long

 

 

Tie

83

7

Image 7
Contents Model No. NTL07707.1 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Assembly See the inset drawing. Tie the long tie Make sure that the power cord is unpluggedNut the Wheel must turn freely. Discard Be careful not to pinch the Upright WireFully tighten the Bolts yet Not fully fold the Frame yetNot to pinch the wires Connectors should slide together easilyPage Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeChange the incline of the treadmill as desired Turn on the fan if desired Measure your heart rate if desiredSelect one of the preset workouts HOW to USE a Preset WorkoutMonitor your progress with the display Insert an iFIT card and select a workout HOW to USE AN Ifit CardInformation Mode HOW to USE the Stereo Sound SystemHOW to Adjust the Cushioning System HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description R0907BQty Exploded Drawing A-Model No. NTL07707.1 Exploded Drawing B-Model No. NTL07707.1 Exploded Drawing C-Model No. NTL07707.1 Exploded Drawing D-Model No. NTL07707.1 Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Related manuals
Manual 32 pages 14.95 Kb