NordicTrack NTL07707.1 user manual Connectors should slide together easily, Not to pinch the wires

Page 9

7. Set the console assembly face down on a soft

7

 

Console

 

surface to avoid scratching the console assem-

 

 

 

 

 

bly. Hold the Right Handrail (95) near the con-

 

 

Wire

 

sole assembly. Next, insert the console wire into

95

1

Hole

 

the large hole in the Right Handrail and out of

 

 

 

 

 

the top as shown. If necessary, use needlenose

 

 

 

1

pliers to pull the console wire out.

 

 

 

 

Attach the Right Handrail (95) and the Left

 

 

 

 

Handrail (not shown) with four #8 x 3/4" Screws

 

 

 

 

(1) (only two are shown). Make sure that no

 

 

 

 

wires are pinched. Start all four Screws be-

 

 

 

 

fore tightening any of them; do not over-

 

 

 

 

tighten the Screws.

 

 

 

 

 

 

 

 

Console

 

 

 

 

Assembly

8. Tighten a 1/4" x 1 1/4" Bolt (5) with a 1/4" Star

8

 

 

 

Washer (33) into the bracket and the Handrail

 

 

 

 

 

5

Wire

Crossbar (94) on each side of the console as-

 

 

 

 

Tie

 

 

 

sembly (only one side is shown).

 

 

 

 

 

33

 

 

 

 

 

Remove the wire tie from the console wire.

Console

Assembly

 

 

 

94

 

9. Remove the long tie from the Upright Wire (38).

9

 

 

 

 

Console

 

 

 

 

 

 

Have a second person hold the console assem-

 

Assembly

 

 

bly near the Right Upright (78) and the Left

 

 

 

 

Upright (not shown). Connect the Upright Wire

 

 

 

 

(38) to the console wire. See the inset drawing.

 

 

 

 

The connectors should slide together easily

 

 

 

 

and snap into place. If they do not, turn one

Console

 

 

connector and try again. IF THE CONNECTORS

 

 

Wire

 

 

 

ARE NOT CONNECTED PROPERLY, THE

 

 

 

 

 

 

 

CONSOLE MAY BE DAMAGED WHEN THE

 

 

 

 

POWER IS TURNED ON.

78

 

 

 

 

38

 

Console

Attach the console assembly to the Right Upright

 

Long

Wire

 

 

(78) and the Left Upright (not shown) with four

 

 

 

 

 

Tie

 

5/16" x 3 1/4" Bolts (7) and four 5/16" Star

 

 

 

 

10

 

 

Washers (10) (only two are shown). Be careful

 

 

38

not to pinch the wires.

7

 

 

 

 

 

 

See steps 4 and 6. Tighten the four 3/8" x 5"

 

 

 

 

Bolts (6).

 

 

 

 

 

9

 

 

 

Image 9
Contents QUESTIONS? Model No. NTL07707.1 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Before YOU Begin Assembly See the inset drawing. Tie the long tie Make sure that the power cord is unpluggedFully tighten the Bolts yet Be careful not to pinch the Upright WireNot fully fold the Frame yet Nut the Wheel must turn freely. DiscardNot to pinch the wires Connectors should slide together easilyPage Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerSelect the manual mode Insert the key into the consoleChange the incline of the treadmill as desired Turn on the fan if desired Measure your heart rate if desiredHOW to USE a Preset Workout Select one of the preset workoutsMonitor your progress with the display Insert an iFIT card and select a workout HOW to USE AN Ifit CardHOW to USE the Stereo Sound System Information ModeHOW to Adjust the Cushioning System HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Page Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyKey No. Qty Description R0907BQty Exploded Drawing A-Model No. NTL07707.1 Exploded Drawing B-Model No. NTL07707.1 Exploded Drawing C-Model No. NTL07707.1 Exploded Drawing D-Model No. NTL07707.1 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Related manuals
Manual 32 pages 14.95 Kb