NordicTrack NTEL59010 user manual Batteries, HOW to USE a Preset Program, Start the program

Page 13
Increase Arrow

moving your hands. When your pulse is detected, the heart-shaped indicator in the display will flash each time your heart beats. After a moment, two dashes (– –) will appear and then your heart rate will be shown.

For the most accurate heart rate reading, continue to hold the handgrips for about 15 seconds. Note: When you first hold the handgrips, the display will show your heart rate continuously for 15 seconds. The display will then show your heart rate along with the other feedback modes.

When you are finished exercising, the console

6 will automatically turn off after five minutes.

If the pedals are not moved and the console but- tons are not pressed for five minutes, the con- sole will automatically turn off to conserve the

batteries.

HOW TO USE A PRESET PROGRAM

1 Turn on the console.

Refer to step 1 on page 12.

2 Select one of the four preset programs.

Each time the console is turned

on, the manual mode will be selected. To select a preset program, press

the Select

Program button repeatedly until the number 1, 2, 3, or 4 appears in the upper right corner of the display.

The profiles numbered 1 through 4 on the left side of the console show the resistance and pace settings for the preset programs. For example, profile number 4 shows that when preset program 4 is selected, both the resistance and the pace will gradually increase during the first half of the program, and then decrease during the last half.

3 Start the program.

To start the program, press the Start Program button or simply begin exercising. Each preset

program consists of twenty, one-minute periods. One resistance setting and one pace setting are programmed for each period. (The same resis- tance setting and/or pace setting may be pro- grammed for consecutive periods.)

During the program, the resistance of the elliptical crosstrainer will automatically change as shown by the applicable profile on the console. If the cur- rent resistance level is too high or too low, you can change the resistance level by pressing the Resistance buttons. However, when the current period of the program is completed, the resis- tance level will automatically change if a different resistance setting is programmed for the next period.

The pace set-

tings for the pro- gram will be shown by the right bar graph in the display. (The

left bar graph will show your actual

exercise pace.) As the right bar graph changes during the program, simply increase or decrease your pace so that the same number of bars appear in both bar graphs. If your pace is slower than the current pace setting, the increase arrow will also appear in the display to prompt you to increase your pace; if your pace is faster than the pace setting, the decrease arrow will appear.

Important: The pace settings for the program are intended only to provide a goal. Your actu- al pace may be slower than the pace settings, especially during the first few months of your exercise program. Make sure to exercise at a pace that is comfortable for you.

During the program, the display will show the time remaining in the program. When no time remains, the program will be completed. If you continue to exercise after the program is completed, the dis- play will continue to show your exercise feedback.

4 Follow your progress with the feedback modes.

Refer to step 4 on page 12.

5 Measure your heart rate if desired.

See step 5 on page 12.

When you are finished exercising, the console

6 will automatically turn off after five minutes.

Refer to step 6 above.

13

Image 13
Contents Model No. NTEL59010 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Front Before YOU BeginBack Right Side Assembly Locknut the Incline Bracket must be able to pivot easily Page Installing the Receiver for the Optional Chest Pulse Sensor Incline Adjustment HOW to USE the Elliptical CrosstrainerHOW to USE the Upper Body Arms HOW to Adjust the PedalsConsole Diagram Features of the Console Refer to the drawing on Console DescriptionHOW to USE the Manual Mode Select one of the four preset programs HOW to USE a Preset ProgramBatteries Start the programSelect one of the two heart rate programs HOW to USE a Heart Rate ProgramEnter your age Hold the handgrip pulse sensorAudio Adapter Cable Headphones HOW to Connect Your Home Stereo HOW to Connect Your Portable StereoAudio Cable HOW to Connect Your VCR HOW to Connect Your ComputerPressVCR. the play button on your CD player or Follow the on-line instructions to start Program HOW to USE Programs Directly from OUR WEB SiteReturn to the elliptical crosstrainer and begin Exercising Maintenance and Troubleshooting Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencyQty Description Part LIST-Model No. NTEL59010NTEL59010No Limited Warranty HOW to Order Replacement Parts