Machine | ParaBody 867101 manual

867101 LAT OPTION ASSEMBLY INSTRUCTIONS

Slide the CARRIAGEdown over the LATUPRIGHTas showI1 on drawing. (MAKESU]~E THAT THE WEIGt~T PEG ON THE. CPJ~RL&GE IS FAC][NG TOWAP~STHE FRONT OF THE

MACHINE)

SECURELYassemble the UPRIGHTEXTENSIONto the top of the UPRIGHTFRAMEas shown in (DETAILB) using one (1) 1/2 X 3 IN. BOLT,the 3/4 X 1/2 X 1-9/t6 IN. SPACER,two (2) 1/2 WASI-~RS,and one (1) 1/2 IN. NUT.

10.LOOSELYassemble three (3) 3-1/2 X 3/8 X 1 IN. PULLEYS,and six (6) 5/8 X 3/8 X SPACERSbetween the PULLEYMOUNTFLATSas shown on drawing using three (3) 3/8 X 3-1/4 IN. BOLTS,six (6) 3/8 IN. WASHERS,and three (3) 3/8 IN. LOCKNUTS. (DO NOTTIGI[TEN THE BOLT CONNECTIONSAT T]~IS TIME)

11.LOOSELYassemble the two (2) PULLEYMOUNTFLATSto the LATUPRIGHT, and the UPRIGtITEXTENSIONas shown on drawing, using two (2) 3/8 X 3-1/4 IN. BOLTS,four (4) 3/8

WASHERS,and two (2) 3/8 IN. LOCKNUTS. (DO NOT TIGHTENTHE BOLT CONNECTIONS AT THIS TIME)

12.Loosen, remove, and discard the top 1/2 X 3-1/4 IN. BOLTthat connects the CROSSBRACEto the UPRIGHTFRAME, and SECURELYassemble file LOWPULLEYSUPPORTto tile UPRIGttT FRAMEas shownon dra~ving using one (1) 1/2 X 3-1/2 IN. BOLT,and re-using the two (2) 1/2 IN.

WASHERS,and file one 1/2 IN. LOCKNUT.

13..LOOSELYassemble one (1) 3-1/2 X 3/8 X 1 IN. PULLEYand orte 5/8 X 3/8 X 1/4 IN. SPACERto file LOWPULLEYSUPPORTas shown on drawing using one (1) 3/8 X 2-1/4 IN. BOLT,two (2.) 3/8 WASHERS,and one (1) 3/8 IN. LOCKNUT. (THIS CONNECTIONWILL BE TIGIITENED AFTER CABLE HAS BEEN ROUTED)

14.LOOSELYassemble two (2) 3-1/2 X 3/8 X 1 IN. PULLEYSbetween two (2) CONNECTORPLATES as shown on drawing using two (2) 3/8 X 2-1/4 IN. BOLTS,four (4) 3/8 IN. WASHERS,and two (2)

IN. LOCK NUTS. (TttIS CONNECTIONWILL BE TIGHTENED AFTER CABLE HAS BEEN

ROUTED)

15.Route the first CABLE(THE ENDWITHOUTWHITEBALL) over file HIGH PULLEYof the PULLEYMOUNTFLATS. Then assemble one (1) 3/8 X 3-1/4 IN. BOLTtwo (2) 3/8 IN. WASHERS, m~d one(l) 3/8 IN. LOCKNUTto file last hole of the PULLEYMOUNTFLATS. (DO NOTOVER TIGHTEN BOLT) (MAKE SURE THAT THE CABLE IS BETWEEN THE PULLEY AND BOLT)

Pull CABLEover and down the SECONDPULLEYof the PULLEYMOUNTFLATS. Rim the CABLEaround one of the PULLEYSassembled ~o the CONNECTORPLATESfrom STEP 14, and up to file THIRD PULLEYof the PULLEYMOUNTFLATS.

Pull CABLEover and down the THIRDPULLEY,to file CARRIAGEAttach. the CABLEtc, the CARRIAGE,using one (1) 5/16 IN. SNAPHOOIC

See CABLEROUTINGDIAGRAMfor help hi completing STEP 15.

5	04./1:;/97