Reebok Fitness RBBE2057.0 manual Attach the other Front Ankle Brace 22 in the same way

Page 11

13.Slide the Lock Frame (11) onto the notched bracket on the Leg Frame (10), and insert the lower end of the Lock Frame into the slot in the Foot Plate (19). Attach the Lock Frame with an M10 x 75mm Button Bolt (57), two

M10 Washers (68), two 16mm Spacers (46), and an M10 Nylon Locknut (65) as shown.

Make sure that the Button Bolt is inserted through the hole in the lower end of the Lock Frame.

See step 12. Tighten the four M4 x 25mm Screws (60).

Pull the Ankle Lock Assembly (33) upward and pivot the Lock Frame (11) over the indi- cated notch in the bracket on the Leg Frame (10). Release the Lock Handle and engage the Lock Frame into the notch.

See the inset drawing. Attach an M8 x 16mm Button Bolt (61) and an M8 Nylon Locknut (72) to the hole in the end of the bracket on the Leg Frame (10).

14.Identify the two Rear Ankle Braces (34), which have holes in the indicated locations.

Slide a Rear Ankle Brace (34) onto the Ankle Brace Tube (18). Attach the Rear Ankle Brace with two M4 x 15mm Screws (58). Make sure that the Screws are tightened into the indi- cated holes in the Ankle Brace Tube. Next, press a 19mm Round Cap (45) into the Ankle Brace Tube, and attach the Round Cap with an M4 x 15mm Screw (58).

Attach the other Rear Ankle Brace (34) to the Ankle Brace Tube (18) in the same way.

15.Slide a Front Ankle Brace (22) onto the round tube on the Lock Frame (11). Next, press a 19mm Round Cap (45) into the round tube, and attach the Round Cap with an M4 x 15mm Screw (58).

Attach the other Front Ankle Brace (22) in the same way.

13

33

 

 

 

 

11

 

 

 

10

 

Notch

 

Slot

46

 

68

 

 

19

 

 

 

 

65

57

 

 

68

46

 

61

72

 

 

 

 

10

 

14

 

 

 

 

34

34

 

 

45

 

 

58

18

Holes

 

Holes

 

 

58

 

15

 

 

 

11

22

22

 

 

 

45

 

 

58

 

 

11

 

 

Image 11
Contents Mon.-Fri a.m.-6 p.m. MST Sat a.m.-4 p.m. MST QUESTIONS?Model No. RBBE2057.0 Serial No Call TOLL-FREETable of Contents Important Precautions Before YOU Begin Assembled DimensionsPart Identification Chart Repeat this step for the Right Base AssemblyMake Assembly Easier Before beginning assembly, make surePage See the inset drawing. Identify the Center Frame Page Screws yet Attach the other Front Ankle Brace 22 in the same way Page Page Selecting the Backrest Frame POSI- Tion AdjustmentAdjusting the LEG Frame Locking the Inversion Table Using the Ankle LockSetting the Inversion Angle Leveling the Inversion TableDo not sit up to return to the starting position Rotating on the Inversion TableDo not attempt to do sit-ups Developing a ProgramBeginner Program Full Inversion ProgramQty Description Part LIST-Model No. RBBE2057.0Exploded DRAWING-Model No. RBBE2057.0 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty