Image IMTL4153.1 user manual Repeat this step on the opposite side of the treadmill

Page 7

2.Open part bag C. See drawing 2a. Locate the Wheel Housings (106). Attach a Wheel (108) to each Wheel Housing with a Wheel Bolt (107) and a Wheel Nut (21) as shown. Do not overtighten the Wheel Bolts.

See drawing 2b. Insert a Wheel Housing (106) into the Base (109). (Note: It may be helpful to use a rubber mallet to fully insert the Wheel Housing.) Press a Base Endcap (99) onto the end of the Base.

Repeat this step on the opposite side of the treadmill.

3.With the help of a second person, carefully tip the Uprights (69, 82) down so the treadmill pivots on the Wheels (108) as shown.

Tighten a 3/4” Screw (6) into one side of the Base (109) and one of the Wheel Housings (106). Attach a long Rear Base Pad (105) and a short Front Base Pad (100) to the Base with four additional 3/4” Screws (6) as shown.

Repeat this step on the opposite side of the treadmill.

With the help of a second person, carefully raise the Uprights (69, 82) to the vertical position.

4.With the help of a second person, hold the Console Base (85) near the Uprights (69, 82) as shown.

Connect the Wire Harness (83) to the wire harness in the Right Handrail Bracket (113). Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try to con- nect them again. IF THE CONNECTORS ARE NOT

CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Insert the wires harnesses into the Right Upright (82).

Open part bag A. Hold the Handrail Brackets (73, 113) on top of the Uprights (69, 82). Finger tighten two 1” Bolts (71) with 5/16” Star Washers (127) into the Handrail Brackets and the tops of the Uprights as shown. Press the Handrail Brackets towards the cen- ter of the treadmill. Then, tighten both Bolts.

2a

106

106

107

 

 

 

 

 

21

107

 

108

 

108

 

 

 

2b

 

 

99

 

 

 

 

 

 

99

 

 

106

 

3

 

 

 

 

69

 

6

 

 

 

82

 

 

100

100

 

 

109

 

 

 

 

 

6

105

 

 

 

106

 

 

109

6

 

 

 

108

 

6

105

 

106

 

6

 

 

 

 

 

108

 

4

 

 

 

71

 

 

 

127

 

 

 

 

73

 

 

 

 

85

 

 

 

69

71

 

 

 

 

 

127

 

 

 

83

 

 

 

113

 

 

83

82

 

 

 

7

Image 7
Contents Mon.-Fri., 6 a.m.-6 p.m. MST QUESTIONS?Model No. IMTL4153.1 Serial No Call TOLL-FREETable of Contents Important Precautions Page Back Before YOU BeginRight Side Base 109 in the same way. Note There is not a wire AssemblyRepeat this step on the opposite side of the treadmill Page Wire Cylinder Treadmill Operation HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerSelect a Quick-Fit speed program HOW to USE a QUICK-FIT Speed ProgramMeasure your heart rate if desired Whenkey. you are finished exercising, removeFollow your progress with the displays HOW to Connect Your Portable Stereo HOW to Connect Your Computer HOW to Connect Your Home StereoAudio Adapter Cable HOW to Connect Your VCRPressVCR. the Play button on your CD player or Insert the key into the consoleFollow your progress with the matrix Displays HOW to USE Programs Directly from OUR WEB SiteFollow the on-line instructions to start Program Return to the treadmill and stand on the footOptional Chest Pulse Sensor Information ModeHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TroubleshootingTop View Problem The walking belt slows when walked on Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Qty Description R0505ADescription Exploded DRAWING-Model No. IMTL4153.1 111 Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT