COMPUTER TIPS AND TROUBLE SHOOTING
STEP 10 – Water Bottle Holder
remove and
phillips screw |
If you have any problems with your Computer: First check this manual to be sure you have followed the assembly instructions correctly.
Computer Installation: Follow Step 9 on page 10 of the Owner's Manual
Computer Tube Assembly: Follow Step 6 on page 9 of this Manual
(Make sure all wire connectors are firmly attached and "click" into place).
If the Computer is powered by batteries and:
The Computer does not illuminate at all
• Reconnect the (10) wire connector at the base of the Computer and |
2 (2) wire connectors connect
Pulse Sensors
computer
back
computer
tube
Installation
a)Remove (2) Phillips Screws from Computer Tube
b)Align holes and attach Water Bottle Holder to Computer Tube with phillips screws removed in Step A
c)Place water bottle in holder
| water bottle | |
| holder | |
| remove and | |
computer | ||
phillips screw | ||
tube | ||
|
the (5) wire connector inside the Computer Tube. |
• Reinstall the batteries using instructions on page 10, step 9. |
Upon
•Install new batteries. Although the batteries are new when they are shipped from the factory, over time they will slowly discharge.
The Computer displays “E 1"
•Make sure the (5) wire connector inside the Computer Tube is securely fastened.
(10)wire connector leads to the motor/magnetic sensor/
AC adapter jack
looking from the left side of the unit
Figure 10 - Install Water Bottle Holder
receptacle
If the Computer is powered by the AC Adapter and:
The Computer does not illuminate at all
•Reconnect the (10) wire connector at the base of the Computer and the (5) wire connector inside the Computer Tube.
The Computer displays “E 1"
•Make sure the (5) wire connector inside the Computer Tube is securely fastened.
NOTE: If the AC Adapter receptacle is plugged into the Computer, but the adapter is not plugged into an AC wall outlet (or has been removed) from the AC wall outlet, the Computer will not display. To reset the Computer, the AC Adapter must be plugged into the AC wall outlet.
If the Computer is powered by Batteries or
AC Adapter and:
The Computer is illuminated but does not display Speed or Distance
•Reconnect the (10) wire connector at the base of the Computer and the the (2) wire connector inside the Computer Tube.
computer
tube
(5) wire | (2) wire | |
connector | ||
connector to | ||
to motor | ||
magnetic | ||
| ||
| sensor |
(4) wire |
connector to |
AC adapter
main
frame
front foot
tube
Figure 11 - AC Adapter
STEP 11 – AC Adapter
a)Plug AC Adapter into receptacle located in the Main Frame near the Front Foot Tube, see Figure 10.
b)Insert AC Adapter plug into outlet in wall.
The Computer is illuminated but does not display a pulse reading
•You must press the START button on the Computer, and have both hands placed firmly on the Pulse Sensors on the Rear Handlebar for the Computer to detect and display your pulse.
NOTE: Depending on what program you have set the Computer to, after pressing the START button, it will take the Computer approximately 6
NOTE: Keeping your Pulse Sensors clean will provide better conductivity between your hands, and the Pulse Sensor.
To insure a more accurate pulse reading, both hands must grab the Pulse Sensors on the Rear Handlebar continuously for approximately 6 seconds.
pulse |
sensors |
main | (3) wire connector |
frame | to AC Adapter |
| receptacle |
GETTING STARTED
Once your Recumbent Bike is assembled, make sure that your workout space has a solid, level surface with plenty of space around it. We recommend placing a mat under your unit to protect your flooring.
Correct Workout Position
When exercising, keep your back straight and your head in a neutral position to minimize neck and upper back strain. When pedaling do not lock out your knees, at the bottom of the pedaling motion there should be a slight bend in the knee. Always try to pedal the bike with a smooth and rhythmic motion.
18 | 11 |