Healthrider HRTL91706.0 manual Shown make sure that all of the holes are

Page 7

2. With the help of a second person, carefully tip

2

 

 

 

 

the treadmill onto its right side as shown.

 

 

 

 

 

 

 

 

 

Insert the other Extension Leg (89) into the base

 

84

 

 

 

 

 

 

65

of the Uprights (84) as shown. Hold two

 

 

 

82

 

 

 

 

Extension Leg Nuts (67) in the bottom of the

 

 

 

 

Extension Leg. Next, insert two Extension Leg

22

 

82

 

 

Bolts (65) into the top of the Extension Leg, and

 

 

 

 

firmly tighten the Extension Leg Bolts into the

 

 

 

 

 

Extension Leg Nuts.

 

 

 

 

58

 

 

 

 

 

Attach two Base Pads (82) to the base of the

 

 

67

89

 

Uprights (84) with two 3/4” Tek Screws (22).

 

 

 

 

 

 

 

 

 

With the help of a second person, carefully raise

 

 

 

 

 

the treadmill so that all four Base Pads (22) are

 

 

 

 

 

on the floor and the Frame (58) is in a vertical

 

 

 

 

 

position (see drawing 4).

 

 

 

 

 

3. Identify the Latch Shock (29).

3

 

 

 

 

 

 

 

 

 

Make sure that the sleeve on the Latch Shock

 

 

 

 

 

(29) is covering hole 1 and that the latch knob is

 

 

 

 

 

engaged in hole 1. If necessary, slide the sleeve

 

Hole 2

 

 

 

over hole 1 and engage the latch knob into hole

 

 

Latch Knob

 

 

 

 

 

1. Then, pull the sleeve to make sure that it is

 

 

 

 

 

locked in place.

 

 

 

Hole 1

 

 

 

 

 

 

Next, make sure that the latch knob is also en-

 

Tube

 

 

29

 

 

 

 

gaged in hole 2. If it is not, pull out the tube until

 

Sleeve

 

 

you see hole 2, and then slide the tube back into

 

 

 

the large barrel until the latch knob engages

 

 

 

 

 

hole 2.

 

 

 

Large

 

 

 

 

 

Barrel

 

4. Remove the plastic ties from the ends of the

4

 

58

 

 

Latch Shock (29).

 

 

 

 

 

 

 

Orient the Latch Shock (29) so that the large

 

 

 

 

 

barrel and the latch knob are positioned as

 

30

50

 

shown; make sure that all of the holes are

 

Top

 

 

aligned (see the inset drawings). Attach the

 

 

 

 

 

 

 

 

 

lower end of the Latch Shock to the bracket on

 

 

 

 

Holes

the Upright (84) with the Lower Latch Shock Bolt

 

Latch Knob

 

29

(39) and a Nut (30).

 

 

 

 

 

 

 

 

 

Then, attach the upper end of the Latch Shock

 

 

 

Large

 

(29) to the bracket on the Frame (58) with the

 

 

 

Barrel

 

Upper Latch Shock Bolt (50) and a Nut (30).

 

 

 

84

 

Note: It may be necessary to move the Frame

 

 

 

 

back and forth to align the Latch Shock with the

 

 

 

 

Holes

Bracket.

 

 

 

 

 

 

 

 

 

 

 

30

 

 

Bottom

 

 

 

39

 

 

 

 

 

 

 

7

 

 

 

 

Image 7
Contents Model No. HRTL91706.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Right Side Before YOU BeginBack Make sure that the power cord is unplugged AssemblyAligned see the inset drawings. Attach Shown make sure that all of the holes areHandrail Bolts and then firmly tighten them Sure to connect the connectors properly seeAgain. if the Connectors are not CON Be Damaged When the Power isSet the console assembly on the Handrail HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Measure your heart rate if desiredSelect one of the nine cross trainer programs HOW to USE a Cross Trainer ProgramPress the Start button to start the program Continue the cross trainer program Perform the first strength exercise when PromptedSelect one of the custom programs HOW to Create a Custom ProgramFollow your progress with the displays HOW to USE a Custom ProgramOptional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Top View Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesKey Qty Description R1206AModel Exploded Drawing B-Model No. HRTL91706.0 R1206A Exploded Drawing C-Model No. HRTL91706.0 R1206A Exploded Drawing D-Model No. HRTL91706.0 R1206A Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT