JVC CA-MXKB1 manual Adjusting the Volume, Fade-out Muting Fade Muting, Selecting the Sound Mode

Page 11

Basic Operations

Adjusting the Volume

Turn the VOLUME control on the Unit clockwise to increase the volume or turn it counterclockwise to decrease the volume.

Press the VOLUME + button on the Remote Control to increase the volume or press the VOLUME – button on the Remote Control to decrease the volume.

You can set the volume level to MIN, 1-30, or MAX.

CAUTION:

•DO NOT turn on the System and/or start playing any source without first setting the VOLUME control to minimum, as a sudden blast of sound could damage your hearing, speakers and/or headphones.

For private listening

Connect a pair of headphones to the PHONES jack. No sound comes out of the speakers.

Be sure to turn down the volume before connecting or putting on headphones.

Fade-out Muting (FADE MUTING)

You can mute the output with one touch operation.

To muting the output, press the FADE MUTING button on the Remote Control. The output is faded out.

To release muting, press the FADE MUTING button once again. The output is faded in to the previous level.

•After Fade-out Muting, turning the VOLUME control on the unit or pressing the VOLUME button on the Remote Control will increase the volume from MIN. setting.

Reinforcing the Bass Sound (ACTIVE BASS EX.)

The richness and fullness of the bass sound is maintained regard- less of how low you set the volume.

You can use this effect only for playback.

To get the effect, press the ACTIVE BASS EX. (Extension) button.

The “ACTIVE BASS EX.” indicator lights up and “BASS ON” appears on the display.

To cancel the effect, press the button again.

The “ACTIVE BASS EX.” indicator goes out and “BASS OFF” appears on the display.

Selecting the Sound Mode

(SOUND MODE)

You can select one of 3 SEA (Sound Effect Amplifier) modes. You can use this effect only for playback.

To get the effect, press the SOUND MODE button until Sound Mode you want appears on the display.

The “SOUND MODE” indicator lights up in the display.

Each time you press the button, the Sound Mode changes as fol- lows:

ROCK = POP = CLASSIC = FLAT = (back to the beginning)

To cancel the effect, press the SOUND MODE button until “FLAT” appears on the display.

The “SOUND MODE” indicator goes off.

ROCK

Boosts low and high frequencies. Good for

POP

acoustic music.

Good for vocal music.

CLASSIC

Set for wide and dynamic sound stereo

FLAT

systems.

No sound effect applies.

Entering the Number with the Remote Control (Numeric Keys)

You will use the number keys on the Remote Control to enter num- bers for presetting stations, recalling the preset stations, or pro- gramming the playing tracks on CDs.

How to enter the number with the number keys is explained here.

Examples:

•To enter number 5, press 5.

•To enter number 15, press OVER, 1, then 5.

•To enter number 20, press OVER, 2, then 0.

For MP3 (For CA-MXKB2 only)

•To enter number 5, press 5.

•To enter number 15, press OVER, 0, 1, then 5.

•To enter number 125, press OVER, 1, 2, then 5.

Changing the Display

Each time you press the DISPLAY button, the display changes as shown below:

Currently selected source Ô Current time

For CD

For CD, see “Changing the Display for CD” on page 15.

8

Page 10 Page 12
Image 11
Page 10 Page 12
Contents CA-MXKB2 CA-MXKB1 If in Doubt Consult a Competent Electrician Important for Laser ProductsAbove ALL How This Manual Is Organized FeaturesIntroduction Table of Contents Getting Started AccessoriesHow To Put Batteries In the Remote Control Using the Remote ControlRear Panel of the Unit Connecting the AM MW AntennaAbout the FM Antenna Connecting External Equipment Connecting the SpeakersCompu Play Connecting to the Wall OutletDemo Mode On the Remote ControlTurning the System On Turning the Power On and OffECO Mode ECO Basic OperationsFade-out Muting Fade Muting Adjusting the VolumeSelecting the Sound Mode Entering the Number with the Remote Control Numeric KeysOne Touch Radio Using the TunerTuning In a Station Select a station using one of the following methodsPress the 4 or ¢ button to select the preset number Presetting StationsTo Change the FM Reception Mode Using the UnitFor MP3 discs Using the CD PlayerWhen playing a CD-R or CD-RW For CA-MXKB2 onlyTo Unload CDs Changing the MP3 Playback ModeTo Load CDs To Select a Track Basics of Using the CD Player- Normal PlayTo Select a Group For MP3 Group mode only To Play CDsTo Exit and Re-enter Program Play Programming the Playing Order of the TracksTo Make a Program To Play the Program You Have MadeUnlocking the Tray Random PlayRepeating Tracks Tray Lock Function Changing the Display for CDTo Fast-Wind a Tape Using the Cassette Deck Listening to a TapePlaying a Tape Tape a CD REC Start Tape B Dubbing Eject Using the Cassette Deck RecordingThings To Know Before You Start Recording REC START/STOPTo Record Any Sound Source to Tape Standard RecordingCD Synchro Recording Tape to Tape Recording DUB- BingAUX Using an External EquipmentListening to the External Equipment Fixing the Clock Using the TimersSetting the Clock Selecting the music source Setting the Daily TimerSetting the OFF time Example Setting the on time ExampleDisplay Setting the REC Recording TimerTurning the Daily Timer On and Off Setting the volume levelSelect the preset station for recording Turning the REC Recording Timer On and OffSetting the on time you want the System to turn on Setting the OFF time you want the System to turn offWait for 5 seconds Setting the Sleep TimerTimer Priority During playback a source, press the Sleep ButtonCare And Maintenance Specification Troubleshooting0404HMMCREORI
Top Page Image Contents