JVC CA-MXKB1, CA-MXKB2 manual Programming the Playing Order of the Tracks, To Make a Program

Page 17

Using the CD Player

Programming the Playing Order of the Tracks

You can program the playing order of the tracks on all the CDs. Note that you can only make a program when the CD Player is stopped.

❏You can program up to 60 tracks in any desired order including the same tracks.

To Make a Program

1Load CDs

2In Stop mode, set the CD Player in Program

Play mode.

On the Unit

Press the PROGRAM button, and the “PROGRAM” indicator blinks on the display.

On the Remote Control

Press the PROGRAM/RANDOM button , and the “PROGRAM” indicator blinks on the display.

Each time you press the button, the display changes as follows: PROGRAM = RANDOM REPEAT = Blank display (Normal Play) = (back to the beginning)

•If a program is already made, the last step of the program will be displayed.

3 Press one of the Disc button (CD1-CD3) to select the CD you want to program.

The display will change to the Program Entry display.

5Repeat steps 3 and 4 to program other tracks on the same CD or the other CD.

6To play the program, Press the CD 6 but-

ton.

For details, see “To Play the Program You Have Made” men- tioned below.

To confirm the programmed contents, while the CD player is stopped, press the SET button.

To delete all the tracks in the program, while the CD Player

is stopped, press the CANCEL button.

•If you try to program a track number that does not exists on the CD, your entry will be ignored.

•If you try to program the 61st track, “FULL” appears on the display.

To Play the Program You Have Made

Press the CD 6 button.

The System plays the tracks in the order you have programmed them.

•To use Repeat Play for Program Play, press the REPEAT but- ton to select “ALL” or “1” before starting playback. For details, see “Repeating Tracks” on page 15.

❏You can skip to a particular program track by pressing the 4 or ¢ button during Program Play.

❏To stop playing, press the 7 button once.

or

Disc number

4Select the track you want to program.

Using the Unit

While the display is blinking, press the 4 or ¢ button to select the track, then press the SET button.

The program order number will be assigned from P-1.

Track number

Disc number

Program order number

Using the Remote Control

Press the numeric keys to directly enter the track number. Then, the program order number will be assigned from P-1.

To Exit and Re-enter Program Play

The program you have made is stored in memory. So, you can exit Program Play temporarily or re-enter Program Play unless you de- lete the program.

To exit the program mode once, while the CD Player is stopped, press the PROGRAM button on the Unit or the PRO- GRAM/RANDOM button on the Remote Control to light off the “PROGRAM” indicator. By changing the source to the other (e.g. Tuner), the CD Player also exits Program Play mode.

To re-enter Program Play mode, press the PROGRAM or PROGRAM/RANDOM button until the “PROGRAM” indicator blinks again.

•Even when the power is turned off (standby or ECO mode), the programmed tracks are not deleted. So, you can re-enter Program Play mode.

14

Page 16 Page 18
Image 17
Page 16 Page 18
Contents CA-MXKB2 CA-MXKB1 If in Doubt Consult a Competent Electrician Important for Laser ProductsAbove ALL How This Manual Is Organized FeaturesIntroduction Table of Contents How To Put Batteries In the Remote Control AccessoriesUsing the Remote Control Getting StartedRear Panel of the Unit Connecting the AM MW AntennaAbout the FM Antenna Connecting External Equipment Connecting the SpeakersDemo Mode Connecting to the Wall OutletOn the Remote Control Compu PlayECO Mode ECO Turning the Power On and OffBasic Operations Turning the System OnSelecting the Sound Mode Adjusting the VolumeEntering the Number with the Remote Control Numeric Keys Fade-out Muting Fade MutingTuning In a Station Using the TunerSelect a station using one of the following methods One Touch RadioTo Change the FM Reception Mode Presetting StationsUsing the Unit Press the 4 or ¢ button to select the preset numberWhen playing a CD-R or CD-RW Using the CD PlayerFor CA-MXKB2 only For MP3 discsTo Unload CDs Changing the MP3 Playback ModeTo Load CDs To Select a Group For MP3 Group mode only Basics of Using the CD Player- Normal PlayTo Play CDs To Select a TrackTo Make a Program Programming the Playing Order of the TracksTo Play the Program You Have Made To Exit and Re-enter Program PlayRepeating Tracks Random PlayTray Lock Function Changing the Display for CD Unlocking the TrayTo Fast-Wind a Tape Using the Cassette Deck Listening to a TapePlaying a Tape Things To Know Before You Start Recording Using the Cassette Deck RecordingREC START/STOP Tape a CD REC Start Tape B Dubbing EjectCD Synchro Recording Standard RecordingTape to Tape Recording DUB- Bing To Record Any Sound Source to TapeAUX Using an External EquipmentListening to the External Equipment Fixing the Clock Using the TimersSetting the Clock Setting the OFF time Example Setting the Daily TimerSetting the on time Example Selecting the music sourceTurning the Daily Timer On and Off Setting the REC Recording TimerSetting the volume level DisplaySetting the on time you want the System to turn on Turning the REC Recording Timer On and OffSetting the OFF time you want the System to turn off Select the preset station for recordingTimer Priority Setting the Sleep TimerDuring playback a source, press the Sleep Button Wait for 5 secondsCare And Maintenance Specification Troubleshooting0404HMMCREORI
Top Page Image Contents