ProForm PFTL81910.1 warranty Assembly, Make sure that the power cord is unplugged

Page 7

ASSEMBLY

•To hire a service technician to assemble this product in your home, call 1-800-445-2480.

•Assembly requires two persons.

•Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you finish assembly.

•The underside of the walking belt is coated with high-performance lubricant. After shipping, there may be some lubricant on top of the walking belt or on the shipping carton. This is normal. If there is lubricant on top of the walking belt, wipe it off with a soft cloth and a mild, non-abrasive cleaner.

•To identify small parts, see page 6.

•Assembly requires the following tools:

the included hex keys

one adjustable wrench one Phillips screwdriver scissors

To avoid damaging parts, do not use power tools for assembly.

1. Make sure that the power cord is unplugged.

1

 

 

 

Place a piece of cardboard below the rear of the

 

 

 

Frame (56) to protect the floor or carpet.

 

 

 

 

Attach the Left Wheel Cap (96) to the Base (94)

 

 

 

56

with two #8 x 3/4" Screws (2).

 

 

 

Attach the Right Wheel Cap (not shown) to

 

 

 

 

the right side of the Base (94) in the same

 

 

 

 

way.

94

2

 

 

 

 

 

 

 

96 Cardboard

 

 

 

2. Pull the Upright Wire (81) and the Base Ground

2

 

 

 

Wire (110) through the indicated hole in the

 

 

 

Base (94).

 

 

 

 

Attach the Base Ground Wire (110) to the Base

 

 

77

 

(94) with a #8 x 1/2" Ground Screw (10).

 

Hole

 

Press the Grommet (77) into the square hole in

81

 

 

the Base (94).

 

 

 

 

 

10

110

94

 

 

 

 

7

 

 

 

Page 6 Page 8
Image 7
Page 6 Page 8
Contents On the WEB QUESTIONS?Model No. PFTL81910.1 Serial No Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Instructions Save TheseBefore YOU Begin Part Identification Chart Make sure that the power cord is unplugged AssemblyBe careful not to pinch the wires. Insert See the inset drawing. Tie the wire tieBase Covers into place yet Assembly Then tighten each of them Again. if YOU do not Connect the CONConsole Assembly Make sure to follow all Instructions in this step Have a second person hold the Frame until is completed HOW to Plug in the Power Cord Operation and AdjustmentConsole Diagram Features of the Console HOW to USE the Manual Mode HOW to Turn on the PowerPage Measure your heart rate if desired. Before using Select an onboard workout HOW to USE AN Onboard WorkoutStart the workout Follow your progress with the displays. See on HOW to USE AN Ifit Live WorkoutSelect an iFit Live workout Start the workout. See onMetric Information ModeMake sure that your audio wire is fully plugged HOW to USE the Stereo Sound SystemHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Move the TreadmillSymptom The power turns off during use TroubleshootingWalking belt or the walking platform unless Symptom The walking belt slows when walked onStructed to do so by an authorized service rep Apply silicone spray or other substances toPage Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Key No. Qty Part ListDescription Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents