ProForm PFTL57105.0 user manual Make sure that no wires are pinched. Hand

Page 7

2.See drawing 2a. Identify the Right Upright (95) and the Left Upright (92); note the orientations of the posts on the Uprights.

See drawing 2b. Hold the Right Upright (95) near the Upright Base (97), and orient the Right Upright as shown.

Make sure that the Right Upright bends in the direc- tion shown.

Straighten the Wire Harness (74), and feed it into the lower end of the Right Upright (95) and out of the upper end. Hold the Right Upright against the Upright Base

(97).Make sure that no wires are pinched. Hand

tighten two Upright Bolts (80) with Upright Star Washers

(4)into the bottom of the Upright Base and the lower end of the Right Upright. Do not tighten the Upright Bolts yet.

With the help of a second person, carefully tip the treadmill onto its right side. Attach the Left Upright (92) as described above. Note: There is not a wire harness on the left side.

Attach the other Wheel (not shown) to the Upright Base (97) as described in step 1.

With the help of a second person, carefully lower the treadmill so the Uprights (92, 95) are in a vertical position.

3.Have a second person hold the Pulse Bar Top (71) be- tween the Uprights (95, 92). See inset drawing 3a. Locate the ground wire on the right end of the Pulse Bar Top. Insert the ground wire through the indicated slot in the post on the Right Upright. See drawing 3b. Locate the pulse wire on the left end of the Pulse Bar Top. Insert the pulse wire into the side of the Left Upright and out of the top as shown.

Next, attach the Pulse Bar Top (71) to the posts on the Uprights (95, 92) with two Screws (108). Make sure that the Screws are in the holes shown. As you tighten the Screws, press the ends of the Pulse Bar Top against the posts. Make sure that no wires are pinched.

4.Attach the ring on the end of the ground wire to the indi- cated hole in the post on the Right Upright (95) with a Silver Ground Screw (23). Make sure that the ring is turned as shown and that the ground wire is routed above or below the head of the indicated Screw

(108). Insert the excess wire into the indicated slot in the post on the Right Upright.

2a

95

Posts

 

 

92

 

2b

 

 

 

 

74

 

Bend

 

 

 

 

 

 

95

97

 

 

 

80

 

 

 

 

4

 

 

3a

 

3b

Pulse

 

 

 

 

 

 

Wire

 

Slot

71

 

 

 

 

Ground

 

Posts

 

108

 

108

Wire

 

 

 

 

 

95

 

92

4

 

 

 

 

 

Slot

108

 

Ground

 

Post

 

 

23

 

Wire

 

95

 

 

 

7

Image 7
Contents Model No. PFTL57105.0 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Right Side Before YOU BeginBack Make sure that the power cord is unplugged AssemblyNut the Wheel must turn freely Make sure that no wires are pinched. Hand Endcaps are oriented exactly as shown Top View 107 Wire Cylinder 108 HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerOnds Handrail-avoid moving your hands. When yourFor the most accurate heart rate reading, con Tinue to hold the contacts for about 15 secSelect one of the six preset programs HOW to USE a Preset ProgramSelect a pulse control program HOW to USE a Pulse Control ProgramFollow your progress with the display Optional Chest Pulse Sensor Information MODE/DEMO ModeHOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Top Exercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Page Description R0605AQty Description Exploded DRAWING-Model No. PFTL57105.0 108 101 100 107 109 111 110 104 105 Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT