ProForm 831.29604.0 user manual Troubleshooting, Problem The power turns off during use, Top

Page 25

TROUBLESHOOTING

Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call toll-free 1-800-4-MY-HOME®(1-800-469-4663).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 10). Use only a single-outlet surge suppres- sor that meets all of the specifications described on page 10. Important: The treadmill is not com- patible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c.Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

c

Tripped

Reset

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please call toll-free 1-800-4-MY-HOME®(1-800-469-4663).

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the Screws (77) from the Hood (1), and carefully pivot the Hood off.

a

77

1

Locate the Reed Switch (10) and the Magnet (18) on the left side of the Pulley (17). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Screw (58), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood, and run the treadmill for a few minutes to check for a correct speed reading.

1/8”

17

58

 

10

18

Top

 

View

 

25

Image 25
Contents Sears, Roebuck and Co., Hoffman Estates, IL Model No Serial NoTable of Contents Important Precautions Page Back Right Side Before YOU BeginMake sure that the power cord is unplugged AssemblyPage Ground Wires Small Hole Sleeve Connector Cover the Upright Wire 42 with the Right Grip Plate HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerWhenkey. you are finished exercising, remove Turn on the fan if desiredSelect a speed & incline program HOW to USE a Speed & Incline ProgramPress the Start button to start the program Select a distance program HOW to USE a Distance ProgramSelect the calorie goal program HOW to USE the Calorie Goal ProgramHOW to Connect Your Portable Stereo HOW to Connect Your MP3 Player or CD PlayerAudio Cable HOW to Connect Your Computer HOW to Connect Your Home StereoPress the Play button on your MP3 player, CD Player, or VCR HOW to Connect Your VCRMeasure your heart rate if desired Follow the on-line instructions to start Program Directly from OUR WEB SiteReturn to the treadmill and stand on the foot Information MODE/DEMO Mode HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked on Exercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencyIf a part is missing, call toll-free Key Qty DescriptionR0905B Sears, Roebuck and Co., Dept WA, Hoffman Estates, IL Full 90 DAY Warranty