ProForm 831.297890 Maintenance and TROUBLE-SHOOTING, Problem The power turns off during use, Top

Page 14

MAINTENANCE AND TROUBLE-SHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll- free at 1-877-897-7493, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the con- sole. (See step 1 on page 9.)

c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

d. Check the on/off switch located on the treadmill near the power cord. The switch must be in the on position.

PROBLEM: The power turns off during use

c

 

Tripped

Reset

d

 

On

 

Position

 

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console. (See step 1 on page 9.)

d. Make sure that the on/off switch is in the on position. (See 1. d. above.)

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the six screws from the hood. Carefully re- move the hood. Locate the Reed Switch (86) and the Magnet (87) on the left side of the Pulley (85). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8Ó. If nec- essary, loosen the Screw (35) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

1/8Ó

85

86

 

 

87

35

 

Top

 

View

 

14

Image 14
Contents Visit OUR Website QUESTIONS?Customer HOT Line SEARS, Roebuck and CO., Hoffman ESTATES, ILTable of Contents Important PrecautionsPage Before YOU Begin Left Side Right SideAssembly Handrail Bolt yetPage Not tighten the Handrail Bolt yet Tighten all parts used in this step and in stepPerformant Lubetm Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Insert the key fully into the console Console DiagramSTEP-BY-STEP Console Operation If the manual mode is selected Press Pressmode.the Mode button to select the desiredSet the desired speed setting Change the incline of the treadmill, if desiredFollow your progress with the four displays When you are finished, remove the keyPulse Sensor TROUBLE-SHOOTING Measure your heart rate, if desiredHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USE Top Maintenance and TROUBLE-SHOOTINGProblem The power turns off during use Problem The walking belt slips when walked on Problem The walking belt slows when walked onProblem The walking belt is off-center when walked on Workout Guidelines Conditioning GuidelinesExercise Intensity Suggested Stretches Part LISTÑModel No Key No. Qty DescriptionExploded DRAWINGÑModel No Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty