JVC RX-5000VBK manual Troubleshooting, Problem Possible Cause Solution

Page 26

Troubleshooting

Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

The display does not light up.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

 

 

 

No sound from speakers.

Speaker signal cables are not connected.

Check speaker wiring and reconnect if

 

 

necessary.

 

 

 

 

The SPEAKERS 1 and 2 buttons are not

Press SPEAKERS 1 and 2 correctly.

 

set correctly.

 

 

 

 

 

An incorrect source is selected.

Select the correct source.

 

 

 

 

Muting is activated.

Press MUTING to cancel the mute.

Sound from one speaker only.

Speaker signal cables are not connected properly.

Check speaker wiring and reconnect if necessary.

The balance is set to one extreme.

Adjust the balance properly (see page 9).

Continuous hiss or buzzing during FM reception.

Incoming signal is too weak.

Connect an outside FM antenna or contact your dealer.

The station is too far away.

Select a new station.

An incorrect antenna is used.

Check with your dealer to be sure you have the correct antenna.

 

Antennas are not connected properly.

Check connections.

 

 

 

Occasional cracking noise during FM

Ignition noise from automobiles.

Move the antenna farther from automobile

reception.

 

traffic.

 

 

 

Howling during record playing.

Your turntable is too close to speakers.

Move speakers away from the turntable.

 

 

 

“OVERLOAD” starts flashing on the

Speakers are overloaded because of high

Rotate the MASTER VOLUME control

display.

volume.

counterclockwise three or four times, then

 

 

press POWER on the front panel.

 

 

If “OVERLOAD” does not disappear, unplug

 

 

the AC power cord, then plug it back again.

Speakers are overloaded because of short circuit of speaker terminals.

Press POWER on the front panel, then check the speaker wiring.

If “OVERLOAD” does not disappear, unplug the AC power cord, then plug it back again.

If speaker wiring is not short-circuited, contact your dealer.

Remote control does not work.

There is an obstruction in front of the

Remove the obstruction.

remote sensor on the receiver.

 

 

 

Batteries are weak.

Replace batteries.

24

Page 25 Page 27
Image 26
Page 25 Page 27
Contents RX-5000VBK For U.S.A Table of Contents Front Panel Remote ControlParts Identification To use the Cursor control buttons q on the front panelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Getting StartedConnecting the front speakers Connecting the SpeakersBasic connecting procedure Connecting the rear and center speakersAudio component connections Connecting Audio/Video ComponentsConnecting the subwoofer speaker If your audio components have a Compu LINK-3 terminalVideo component connections VCRPlug the power cord into an AC outlet Connecting the Power CordPutting Batteries in the Remote Control + to + and toBasic Operations Turning the Power On and Off StandbyFrom the remote control On the front panelRecording a Source Muting the SoundSelecting the Front Speakers Adjusting the Tone Attenuating the Input SignalAdjusting the Front Speaker Output Balance Reinforcing the BassSetting Center and Rear Speakers for DSP Modes Changing the Source NamePress ONE Touch Operation Storing the Basic Settings Adjustments One Touch OperationUsing the Sleep Timer Receiving Radio Broadcasts Tuning in Stations ManuallyUsing Preset Tuning Press FM or AMSelecting the FM Reception Mode DAP modes Using the DSP Modes3D-PHONIC modes Surround ModesAvailable DSP Modes According to the Speaker Arrangement Speaker arrangements Available DSP modesAdjusting the 3D-PHONIC Modes Adjusting the DAP ModesRear speaker output level Press Rearl / + to adjustPress Surround repeatedly Output balanceActivating the DSP Modes Press Surround repeatedly Until the DSP mode you wantTo cancel the DSP mode Select and play a sound sourceUsing the DVD Multi Playback Mode Activating the DVD Multi Playback ModeSame time Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionCassette deck Operating JVC’s Audio/Video ComponentsSound control section Amplifier TunerDVD player CD player-changerMD recorder Troubleshooting Problem Possible Cause SolutionFM tuner IHF SpecificationsAmplifier AM tunerHOW to Locate Your JVC Service Center Limited Warranty AUDIO-2 1299HIMMDWJEIN

RX-5000VBK specifications

The JVC RX-5000VBK is a powerful and versatile audio receiver that offers a rich set of features for both home theater enthusiasts and casual listeners. This unit is designed to deliver excellent sound quality, impressive connectivity options, and user-friendly operation.

One of the standout features of the RX-5000VBK is its ability to deliver high-fidelity audio with clarity and depth, making it an ideal choice for those who value sound quality. With an output of 100 watts per channel, this receiver can drive a variety of speakers, ensuring that users get the best possible performance whether they are enjoying music or watching movies.

The RX-5000VBK integrates advanced surround sound processing capabilities, supporting formats like Dolby Digital and DTS. This processing allows users to experience immersive audio, bringing movies and music to life in a way that's rich and engaging. The unit also includes a built-in equalizer, which allows users to customize their listening experience by adjusting bass and treble settings to their preference.

Connectivity is another strong point of the JVC RX-5000VBK. The receiver comes equipped with multiple HDMI inputs that support 4K video pass-through, enabling users to connect their favorite devices such as Blu-ray players, gaming consoles, and streaming devices without sacrificing video quality. Additionally, there are various analog and digital audio inputs, including optical and coaxial options, making it easy to connect vintage components as well.

The user interface of the RX-5000VBK is designed for simplicity, featuring an intuitive layout that makes it easy to navigate through settings and modes. The included remote control enhances this convenience, allowing users to make adjustments from the comfort of their seating area. Furthermore, the receiver features a built-in AM/FM tuner with programmable presets, enabling users to enjoy their favorite radio stations with ease.

The design of the RX-5000VBK is both stylish and functional, featuring a sleek black finish that can fit well with any home décor. The unit’s compact form factor ensures it can be integrated into various home setups without taking up too much space.

In summary, the JVC RX-5000VBK is a feature-rich audio receiver that excels in delivering high-quality sound, versatile connectivity options, and user-friendly operation. With its combination of advanced technologies and thoughtful design, it stands as an excellent choice for anyone looking to enhance their audio experience at home.
Top Page Image Contents