ProForm PFTL14511.0 warranty HOW to USE the Maintenance Mode

Page 27

HOW TO USE THE MAINTENANCE MODE

The console features a maintenance mode that allows you to calibrate the incline and speed of the treadmill, update the console firmware, calibrate the screen, view technical information, and perform a network test.

1.Select the settings mode. See step 1 on page 25.

2.Select the maintenance mode.

Touch the Maintenance button in the lower right corner of the screen to

enter the maintenance mode.

The maintenance mode main screen will show

information about the model and version of the treadmill. If the console is connected to the con- troller of the treadmill, the controller dot will be green; if it is not, the dot will flash. If the treadmill is connected to your wireless network, the network dot will be green; if it is not, the dot will be black.

3.Calibrate the incline system of the treadmill. Touch the Calibrate Incline button. Then, touch the Begin button to calibrate the incline system. The treadmill will automatically rise to the maximum in- cline level, lower to the minimum incline level, and then return to the starting position. This will cali- brate the incline system. Press the Cancel button to return to the maintenance mode. When the in- cline system is calibrated, touch the Finish button.

IMPORTANT: Keep pets, feet, and other objects away from the treadmill while the incline system is calibrating. In an emergency, pull the key from the console to stop the incline calibration.

4.Calibrate the speed of the treadmill. Calibrate the speed of the treadmill only if in- structed to do so by an authorized service repre- sentative.

Note: The Calibrate Speed button may not be en- abled on your treadmill.

5.Update the console firmware.

For the best results, regularly check for firmware updates.

Touch the Firmware Update button. Next, touch the WiFi button to check for firmware updates using your wireless network. Then, touch the Begin button to check for updates or the Cancel button to return to the maintenance mode.

To avoid damaging the treadmill, do not turn off the power or remove the key while the firmware is being updated.

Note: If you cannot update the console firmware over your wireless network, you can update the firmware using a USB drive. Touch the USB button to install firmware updates using a USB drive. Go to www.iFit.com and download the firmware update onto your USB drive. Safely remove the USB drive from your computer and plug it into the USB port on the top of the console. Touch the Begin button to update the firmware or touch the Cancel button to return to the maintenance mode.

The screen will show the progress of the update. When the update is complete, the treadmill will turn off and then turn back on. If it does not, press the power switch into the off position. Wait for several seconds, and then press the power switch into the reset position. It may take a few minutes for the console to be ready for use.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents On the WEB QUESTIONS?Model No. PFTL14511.0 Serial No Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Instructions Save TheseBefore YOU Begin Wrench Scissors AssemblySee the inset drawing. Tie the wire tie Make sure that the power cord is unpluggedBase Covers into place yet Be careful not to pinch the UprightTighten the Bolts yet. Note It may be helpful Attach the Right Upright not shownAttach the Right Handrail 87 in the same way Important To avoid damaging Shown. Start all four Screws, and then tighten Each of themAgain. if YOU do not Connect the CON Them All four Bolts, and then tighten eachConsole Make sure the caps remain in the ends Storage Latch Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Diagram Features of the ConsoleConsole HOW to SET UP the Console HOW to Turn on the PowerHOW to USE the Manual Mode Begin working outInsert the key into the console Page Turn on the fan if desired Measure your heart rate if desired. Before usingStart the workout HOW to USE AN Onboard WorkoutHOW to USE AN Ifit Live Workout Ifit Live FCC Information HOW to USE the Internet Browser Select the wireless network mode HOW to USE the Settings ModeSelect the unit of measurement Exit the settings modeLog in to your iFit Live account Select a languageSelect the settings mode. See on Select the maintenance mode HOW to USE the Maintenance ModeView technical information HOW to USE the Stereo Sound SystemHOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Move the TreadmillTroubleshooting Problem The power turns off during useOutlets Problem The walking belt slows when walked on TopTurn if the walking belt has shifted to the right Problem The buttons on the screen do not work correctly Problem The iFit Live mode does not function correctlyExercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description Part ListQty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Related manuals
Manual 40 pages 49.67 Kb
Top Page Image Contents