ProForm PFEL05900 manual Front, View

Page 8

9.Connect the Extension Wire (51) to the corresponding wire on the Console (87).

Next, connect the two Pulse Wires (86) to the two remaining wires on the Console (87). Note: Either Pulse Wire can be attached to either wire on the Console.

Next, connect the ground wire to the indicated hole in the Console Plate (91) with an M4 x 16mm Screw (35).

Carefully feed the wires down into the Upright (2). Attach the Console Base (49) to the Upright with four M4 x 16mm Screws (35). Be careful to avoid pinch- ing the wires.

10.Identify the Left Pedal Arm (3), which has an ÒLÓ sticker on it. Be careful not to confuse the Left Pedal Arm with the Right Pedal Arm (not shown); look at the position of the round tube in the inset drawing to identify the Left Pedal Arm. Next, identify the Left Pedal (41), which has the letter ÒLÓ molded onto the bottom.

Turn over the Left Pedal Arm (3) as shown. Insert the three plastic posts on the Left Pedal (41) into the three indicated holes in the Left Pedal Arm. Make sure that the Left Pedal is turned as shown. Attach the Left Pedal with three M4 x 16mm Flange Screws (43).

Attach the Right Pedal (not shown) to the Right Pedal Arm (not shown) in the same way.

11.Apply grease to an M8 x 108mm Bolt (79). Slide an M8 Washer (81) onto the Bolt and insert the Bolt into the indicated side of the Left Pedal Arm (3). Be care- ful not to confuse the Left Pedal Arm with the Right Pedal Arm (not shown); look at the position of the round tube to identify the Left Pedal Arm.

Next, slide a Spacer (44), a Pedal Wheel (77), and another Spacer (44) onto the Bolt and push the Bolt through the other side of the Left Pedal Arm.

Next, slide a Tube Spacer (82), a Chrome Tube (21), and an M8 Washer (81) onto the M8 x 108mm Bolt (79). Tighten an M8 Nylon Locknut (80) onto the Bolt.

Attach the other Chrome Tube (not shown) to the Right Pedal Arm (not shown) in the same way.

8

9

 

 

 

 

 

 

49

 

 

 

87

 

 

 

 

 

Ground Wire

35

 

 

 

 

86

 

 

 

 

35

 

 

Console

 

 

 

Wires

91

 

 

 

 

 

 

 

 

51

 

 

 

 

35

2

 

 

 

10

 

 

 

 

 

 

43

 

 

 

 

 

3

 

 

 

 

 

 

 

Open Side

 

41

Plastic Posts

 

 

 

3

Round

 

 

 

Tube

 

 

 

 

 

 

Open Side

 

 

 

11

 

 

 

 

 

 

 

21

 

 

 

Grease

 

 

 

 

 

81

82

80

 

 

 

81

 

 

 

 

 

 

 

 

 

 

 

 

 

Round

 

 

 

 

 

Tube

79

44

 

 

 

 

44

77

3

 

 

 

11a

82

3

 

 

Front

 

81

 

View

 

 

 

 

 

 

 

 

 

80

21

 

 

 

79

81

 

 

 

 

 

44

77

44

 

 

Image 8
Contents Customer HOT Line QUESTIONS?Model No. PFEL05900 Serial No Table of Contents Important Precautions Before YOU Begin FrontRight Side BackAssembly Locknut the Incline Bracket must pivot easily Be careful not to pinch the wires Front ViewPage Exercising on the Elliptical Crosstrainer HOW to USE the Elliptical CrosstrainerHOW to Adjust the Resistance Incline Adjustment Description of the Console Using the Upper Body ArmsHOW the Pacer Programs Operate STEP-BY-STEP Console OperationHOW to Select Miles or Kilometers Not to pull on Pulse sensor, peel off WiresPlastic before using the pulse sensor Speed, time, dis- tance, lap, or calorie modeÑ RepeatedlyBattery Replacement Maintenance and TROUBLE-SHOOTINGPulse Sensor TROUBLE-SHOOTING Conditioning Guidelines Exercise IntensityUnconditioned Conditioned Training Zone AGE BEATS/MIN Workout GuidelinesSuggested Stretches Page Part LISTÑModel No. PFEL05900 Key Qty DescriptionPDRAWINGÑModelEXPLODEDFEL05900No Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT HOW to Order Replacement PartsLimited Warranty