ProForm PCTL62590 user manual Maintenance and TROUBLE-SHOOTING, Solution, Power Cord

Page 12
2 (14-gauge) cord of

MAINTENANCE AND TROUBLE-SHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department toll- free at 1-888-936-4266, Monday through Friday, 8h00 until 18h00 Eastern Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page

8.) Use only a CUL-listed surge suppressor, rated at 15 amps, with a 1mm 1,5 m (5 ft.) or less in length.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the con- sole. (See step 1 on page 8.)

c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

d. Check the on/off switch located at the front of the treadmill near the power cord. The switch must be

in the on position.

PROBLEM: The power turns off during use

c

 

Tripped

Reset

d

 

On

 

Position

 

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c.Unplug the power cord, wait for five minutes, and then plug the power cord back in.

d.Remove the key from the console. Reinsert the key fully into the console.

e.Make sure that the on/off switch is in the on position.

f.If the treadmill still will not run, please call our Customer Service Department.

PROBLEM: The displays of the console do not function properly

 

SOLUTION:

a. Remove the key from the console and

UNPLUG THE

 

POWER CORD.

Next, remove the screws from the

 

hood and carefully remove the hood. Locate the Reed

 

Switch (97) and the Magnet (9) on the left side of the

 

Pulley (10). Turn the Pulley until the Magnet is aligned

 

with the Reed Switch.

Check the gap between the

 

Magnet and the Reed Switch—it should be about 3

mm(1/8 in.). If necessary, loosen the Screw (98) and move the Reed Switch slightly. Retighten the Screw.

Reattach the hood and run the treadmill for a few min- utes to check for a correct speed reading.

a

 

 

3 mm

98

10

97

9

Top

 

View

 

12

Image 12
Contents QUESTIONS? Model No. PCTL62590 Serial NoSerial Number Decal Table of Contents Important PrecautionsTreadmill is capable of high speeds Pulse sensor is not a medical deviceMove the Treadmill on This treadmill is intended for in-home useBefore YOU Begin For your benefit, read this manual carefully beforeLeft Side Assembly Assembly requires two peoplePose of the packing materials until assembly is completed Adjustable wrench ScissorsIly, turn them do not force them together Tighten all parts used in steps 3, 4, 5Make sure that all parts are tightened before you Operation and Adjustment Trician to determine if the outlet box cover isRight GroundedIs in the console when the power cord is plugged Pressmode. the Mode button to select the desiredSTEP-BY-STEP Console Operation Insert the key fullyIf the manual mode is selectedAs you exercise Press the START/STOP buttonIf a workout program is selected The speed Four displaysWhen you are finished, remove the key Information Mode7Measure your heart rate, if desired Press too hard Or the circulation Your thumbHOW to Fold the Treadmill for Storage HOW to Move the TreadmillHOW to Lower the Treadmill for USE Maintenance and TROUBLE-SHOOTING SolutionPower Cord Problem The walking belt slows when walked on Come damaged. Remove the keyIf the walking belt has shifted to the left Remove the keyConditioning Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyOrdering Replacement Parts Limited Warranty Icon of CANADA, 900 de l’Industrie, St. Jerôme, QC J7Y 4B8Is a registered trademark of Icon Health & Fitness, Inc Part No R1101ASave this page for future reference Part LIST-Model No. PCTL62590 Key Qty DescriptionFrame Incline Bolt R1101A