ProForm PCTL62590 Assembly requires two people, Adjustable wrench Scissors, Handrail Bolt yet

Page 5

ASSEMBLY

Assembly requires two people.

Set the treadmill in a cleared area and remove all packing materials. Do not dis-

 

pose of the packing materials until assembly is completed.

Assembly requires the included allen wrench

 

and your own phillips screwdriver

, adjustable wrench

, and scissors

.

1.With the help of a second person, carefully raise the treadmill to the upright position. While a second person tips the treadmill to one side slightly and holds it, insert one of the Extension Legs (59) into the base of the Uprights (32) as shown. Make sure that the Extension Leg is turned so the bracket is on top. Using the Allen Wrench (102), tighten one of the two Extension Leg Screws (57) into the Base and the Extension Leg. Next,

tip the treadmill to the other side

and attach the other

Extension Leg in the same way.

 

With the help of a second person, carefully lower the treadmill so that both Extension Legs (59) are resting flat on the floor.

2. Refer to HOW TO LOWER THE TREADMILL FOR

USE on page 11. Follow the instructions in step 2 to lower the treadmill.

Without removing the tape from the Latch (34), hold the Latch against the left Upright (32) as shown. Attach the Latch to the left Upright with four Catch Screws (33).

Make sure that the Screws are tight, but do not overtighten them; if the Screws are overtightened,

the Latch will not slide smoothly. After the Latch is attached, remove any visible tape.

Note: The inset drawing shows how the parts of the Latch (34) fit together.

3.Cut the plastic tie holding the cage nut in the upper end of the Left Handrail (60).

Position the Left Handrail (60) on the left Upright (32) as shown. The bracket on the Extension Leg (59) should

be inside of the lower end of the Left Handrail. Thread

a Handrail Bolt (30) with a Handrail Washer (31) into the

left Upright and the Left Handrail.

Do not tighten the

Handrail Bolt yet.

 

1

 

 

32

 

59

102

 

 

57

 

Bracket

 

 

2

 

 

32

 

 

34

 

Spacer

 

 

33

 

Springs

 

 

33

 

Latch

 

 

 

 

Bracket

3

 

 

 

30

 

 

31

60

 

 

 

32

 

 

59

 

5

Image 5
Contents Serial Number Decal QUESTIONS?Model No. PCTL62590 Serial No Important Precautions Table of ContentsPulse sensor is not a medical device Treadmill is capable of high speedsMove the Treadmill on This treadmill is intended for in-home useLeft Side Before YOU BeginFor your benefit, read this manual carefully before Assembly requires two people AssemblyPose of the packing materials until assembly is completed Adjustable wrench ScissorsMake sure that all parts are tightened before you Ily, turn them do not force them togetherTighten all parts used in steps 3, 4, 5 Trician to determine if the outlet box cover is Operation and AdjustmentRight GroundedPressmode. the Mode button to select the desired Is in the console when the power cord is pluggedSTEP-BY-STEP Console Operation Insert the key fullyPress the START/STOP button If the manual mode is selectedAs you exerciseIf a workout program is selected The speed Four displaysInformation Mode When you are finished, remove the key7Measure your heart rate, if desired Press too hard Or the circulation Your thumbHOW to Lower the Treadmill for USE HOW to Fold the Treadmill for StorageHOW to Move the Treadmill Power Cord Maintenance and TROUBLE-SHOOTINGSolution Come damaged. Remove the key Problem The walking belt slows when walked onIf the walking belt has shifted to the left Remove the keyExercise Intensity Conditioning GuidelinesWorkout Guidelines Exercise FrequencyOrdering Replacement Parts Icon of CANADA, 900 de l’Industrie, St. Jerôme, QC J7Y 4B8 Limited WarrantyIs a registered trademark of Icon Health & Fitness, Inc Part No R1101ASave this page for future reference Frame Incline Bolt Part LIST-Model No. PCTL62590Key Qty Description R1101A