ProForm 595Pi user manual

Page 7

2.Orient the Right Upright (36) so the square hole near the lower end is in the position shown. Attach the Right Upright to the Upright Base (48) with two Upright Bolts (40) and two Upright Star Washers (39). Do not tighten the Upright Bolts yet.

Attach each Wheel (45) to the Upright Base (48) with a Wheel Bolt (89), two Wheel Spacers (44), and a Nut (47) as shown. Do not overtighten the Wheel Bolts; the Wheels should turn freely.

3.Cut the tie securing the Wire Harness (28) in a bundle. Do not remove the large colored tie on the end of the Wire Harness.

Orient the Upright Base (48) so the Wheels (45) are at the bottom. Next, position the Upright Base and the Uprights (31, 36) around the frame assembly as shown.

Have another person lift the front of the frame assembly and hold it. Insert the Wire Harness (28) into the square hole near the lower end of the Right Upright (36) and out of the top. Next, raise the Uprights (31, 36) so the Upright Base (48) is flat on the floor. Make sure that the end of the Wire Harness does not fall into the Right Upright; it may be helpful to hold the colored tie on the end of the Wire Harness.

2

 

44

 

36

 

89

 

 

 

 

47

 

 

45

45

44

 

44

47

 

 

 

89

 

 

 

Square Hole

39

 

 

 

48

 

 

 

40

3

 

Hole

 

 

31

 

48

 

 

28

36

45

Frame Assembly

Colored Tie

 

28

 

4.Open the included grease packet, and apply grease to both sides of each Frame Spacer (34).

Hold one of the Frame Spacers (34) between the frame assembly and the Right Upright (36); make sure that the Frame Spacer is oriented as shown in the inset drawing. Insert a Frame Bolt (32) through a Frame Washer (33), the Right Upright, the Frame Spacer, and the bracket on the frame assembly. Be careful not to pinch the Wire Harness (28) in the Right Upright. Tighten a Nut (47) several turns onto the Frame Bolt, but do not fully tighten the Nut yet.

Repeat this step on the left side. Note: There is not a wire harness on the left side.

Remove the colored tie from the Wire Harness (28).

7

4

Left

28

Side

 

 

34

 

Right

 

Side

36

 

 

Bracket

 

47

 

33

34

32

Frame Assembly

 

Image 7
Contents Model No. PFTL43105.3 Serial No QUESTIONS?Call TOLL-FREE Table of Contents Important Precautions Page Right Side Before YOU BeginBack Make sure that the power cord is unplugged AssemblyPage Sure that the Wire Harness 28 is not pinched Top View Frame BoltsPage HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to Turn on the Power HOW to USE the Manual Mode Turn on the fan if desired Measure your heart rate if desiredWhenkey. you are finished exercising, remove Whenkey. the program is completed, remove HOW to USE a Trainer ProgramSelect a trainer program Follow your progress with the displaysSelect a custom program HOW to Create a Custom ProgramHOW to USE a Custom Program Information MODE/DEMO Mode HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingTop Problem The walking belt slows when walked onExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesKey No. Qty Description Part LIST-Model No. PFTL43105.3R0606A Limited Warranty HOW to Order Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Related manuals
Manual 26 pages 26.2 Kb