PART |
| R0806A | |||
Key No. Qty. | Description | Key No. Qty. | Description | ||
1 | 1 | Base | 51 | 1 | Belt |
2 | 1 | Frame | 52 | 1 | Flywheel |
3 | 1 | Upright | 53 | 1 | “C” Magnet |
4 | 1 | Console Bracket | 54 | 1 | Pillow Block |
5 | 1 | Console | 55 | 1 | Magnet |
6 | 1 | Front Stabilizer | 56 | 1 | Spring |
7 | 1 | Rear Stabilizer | 57 | 1 | Idler |
8 | 1 | Left Handlebar | 58 | 1 | Idler Bracket |
9 | 1 | Right Handlebar | 59 | 1 | Clamp |
10 | 2 | Handlebar Endcap | 60 | 1 | Reed Switch Bracket |
11 | 1 | Left Upper Body Arm | 61 | 1 | Base Pin |
12 | 1 | Right Upper Body Arm | 62 | 2 | Latch Bracket Spacer |
13 | 1 | Left Pedal | 63 | 2 | Hair Pin |
14 | 1 | Left Pedal Leg | 64 | 1 | Latch Bracket |
15 | 1 | Right Pedal | 65 | 1 | Pivot Bracket |
16 | 1 | Right Pedal Leg | 66 | 2 | Pivot Bracket Spacer |
17 | 2 | Upright Cover | 67 | 1 | Frame Pin |
18 | 1 | Left Front Handlebar Cover | 68 | 1 | Latch Button |
19 | 1 | Left Rear Handlebar Cover | 69 | 1 | Roll Pin |
20 | 1 | Right Front Handlebar Cover | 70 | 1 | Motor |
21 | 1 | Right Rear Handlebar Cover | 71 | 1 | Resistance Cable Pulley |
22 | 1 | Water Bottle Holder | 72 | 1 | Resistance Cable Set |
23 | 2 | Front Stabilizer Endcap | 73 | 2 | Foam Grip |
24 | 2 | Rear Stabilizer Endcap | 74 | 1 | Pivot Axle |
25 | 2 | Wheel | 75 | 2 | Hub Cover |
26 | 1 | Base Foot | 76 | 2 | Adjustment Knob |
27 | 2 | Leveling Foot | 77 | 4 | M6 x 20mm Button Screw |
28 | 1 | Left Side Shield | 78 | 4 | M8 x 41mm Button Bolt |
29 | 1 | Right Side Shield | 79 | 7 | M8 Jamnut |
30 | 6 | Upper Body Bushing | 80 | 1 | M8 x 69mm Button Bolt |
31 | 4 | Pedal Leg Cover | 81 | 2 | M10 Nylon Locknut |
32 | 2 | Pedal Leg Axle | 82 | 2 | M10 x 82mm Button Screw |
33 | 4 | Pedal Leg Bushing | 83 | 2 | M10 x 127mm Button Screw |
34 | 1 | Base Axle | 84 | 8 | M8 x 23mm Button Screw |
35 | 2 | Base Bushing | 85 | 1 | M6 x 10mm Button Screw |
36 | 1 | Left Crank Arm | 86 | 2 | Crank Screw |
37 | 2 | Adjustment Arm Cover | 87 | 8 | Hub Screw |
38 | 2 | Crank Hub | 88 | 8 | M8 Washer |
39 | 1 | Pulley Spacer | 89 | 2 | M10 x 60mm Button Screw |
40 | 1 | Pulley | 90 | 3 | M8 Split Washer |
41 | 2 | Adjustment Arm | 91 | 1 | Flywheel Spacer |
42 | 4 | Crank Bushing | 92 | 1 | Flywheel Washer |
43 | 2 | Crank Bushing Sleeve | 93 | 1 | Flywheel Snap Ring |
44 | 2 | Crank Bearing Set | 94 | 4 | Pillow Block Screw |
45 | 1 | Crank | 95 | 1 | Stop Screw |
46 | 1 | Crank Spacer | 96 | 1 | M8 x 35mm Screw |
47 | 2 | Crank Snap Ring | 97 | 1 | “E” Clip |
48 | 1 | Upper Wire Harness | 98 | 4 | Pulley Screw |
49 | 1 | Lower Wire Harness | 99 | 2 | Adjustment Pin |
50 | 1 | Reed Switch/Wire | 100 | 2 | M4 x 25mm Screw |
20